Replacement Seal for TRP GS-2250DLR

Question

Question:

I have a 2018 venture 3 axel boat trailer. It has grease seals marked gs-2250DLR also it is marked as TRP. I see you have the gs-2250DL. The seals I have are rubber do you carry these?

asked by: Robert K

0

Expert Reply:

The seal you're looking for is the Grease Seal - Double Lip - 2.250" ID - 3.376" OD - GS-2250DL # GS-2250DL; the TRP is just the manufacturer of that particular seal, which is Tru-Ryde Products, the manufacturer of the part I've mentioned above. These seals have an inner diameter of 2.25 inches, outer diameter of 3.376 inches and also are double lip seals.

expert reply by: Erik B

0

Answer 1

To replace your Dexter 10-36 grease seals I recommend using Grease Seal #GS-2250DL. This seal has an inner diameter of 2.25" and outer diameter of 3.376". This is a double lip seal.

view full answer...

Answer 2

From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you…

view full answer...

Answer 3

Based on my research a hub with a part number 46845 is a hub with a 5 on 4-1/2" bolt pattern and uses inner bearing #L68149 and outer bearing #L44649 like what the bearing kit part #BK2-100 that you referenced provides. The axle should have…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

If you remove the hub and wipe away the grease on the spindle you can check to see if it is damaged. Look for an scarring, gouges, discoloration, or scoring on the spindle. If the spindle is damaged then the bearings won't ride properly and can…

view full answer...

Replacement Seal for TRP GS-2250DLR

Product Page this Question was Asked From

Continue Researching