Replacement Waste Valve for RV Black Water Tank

Question

Question:

Not sure what happened over the winter, but I went out to the trailer and discovered the valve laying on the ground. All the bayonet gripsfoot but one were broken off. Since that part is ring that rotates around the fixture, can it be replaced and if so, do you sell the bayonet ring?

asked by: Daryl L

0

Expert Reply:

I suggest replacing with the Valterra Waste Valve for RV Black Water Tank - Twist On - 3" Bayonet Hooks to 3" Lug
Item # T58. We offer this as a complete replacement assembly.

expert reply by: Michael R

0

Answer 1

You can install part #T58 at the end of the pipe with the stock valve open all the time. Installing this is going to make life a lot easier and you won't have to crawl under your camper. I do recommend part #A05-0303 as well. The cement is…

view full answer...

Answer 2

Your thinking is 100% correct here. RV black water drains will be a standard 3" size, which is the internal diameter of the pipes, so the Valterra Waste Valve for RV Black Water Tank - Twist On - 3" Bayonet Hooks to 3" Lug…

view full answer...

Answer 3

I went out to the warehouse to measure the overall depth of the Valterra Twist-On Waster Valve, #T58, for you. It has an overall depth of 5-1/16 inches. I have included a picture showing this for you.

view full answer...

Answer 4

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 8

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 9

With the weight of your camper I recommend the Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL35FJ. I prefer these as they have the internal jounce bumper which helps to reduce the bounce that is often associated with towing a trailer and…

view full answer...

Answer 10

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 11

Yes, you can replace your current Lippert Equa-Flex equalizers with the MORryde AllTrek 4000 Equalizers #MR29DR on your 2018 Highland Open Range. The yellow octagons on the front and rear are a for correcting the alignment of the axles and are not…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement Waste Valve for RV Black Water Tank

Product Page this Question was Asked From

Continue Researching