Distance From Outside of Roller to Outside of Plate For CE Smith Spool Roller Assembly CE10400G

Question

Question:

Can you tell me the dimension where the “?” In the photo? I am looking for the dimension from the outside of the roller to the outside of the plate that has the two slots in it.

asked by: Rich R

0

Expert Reply:

While the photo did not come through, I can tell you that the dimension from the outside of the roller (with the caps) to the outside of the plate is 4-7/8 inches for the CE Smith Spool Roller Assembly for Boat Trailers - Galvanized Steel and Black Rubber - 4" # CE10400G.

expert reply by: Kyle S

0

Answer 1

I went out to the warehouse and pulled a Offset Spool Roller Assembly, #CE32150G. Measuring from the bottom of the base to the top of the roller in the center section it is 3-3/8 inches. From the bottom of the base to the taller part at either end is…

view full answer...

Answer 2

I went out to the warehouse to measure the internal width of CE Smith roller #CE32110G. It measure 1-7/8 inches. I have included a picture showing this measurement for you.

view full answer...

Answer 3

Most keel rollers for boat trailers like the CE Smith Keel Roller for Boat Trailers part #CE29519 or CE Smith Keel Roller for Boat Trailers - Self Centering part #CE29505 don't have listed weight capacities as they aren't supporting the full…

view full answer...

Answer 4

We don't offer a flat roller assembly, but the 5 inch #CE10401G assembly has a roller that's more flat that might work well for you. The flatter profile would spread more of the boat's weight out over a larger area.

view full answer...

Answer 5

I have a few options to help with loading the boat on the trailer but the best would have to be the CE Smith Keel Roller for Boat Trailers part #CE29505. In order to mount them you'd need the Roller Shaft with Pal Nuts part #CE10727A and CE Smith…

view full answer...

Answer 6

First, roller with bracket #CE32100G is not going to work because the mounting holes on it are spaced 3 inches apart on center so it would be too wide. It measure approximately 2-1/2 inches from the bottom of the bracket to the center of the shaft.…

view full answer...

Answer 7

When it comes to replacing the spool roller on The CE Smith Offset Spool Roller Assembly for Boat Trailers - Galvanized Steel w/ Black Rubber - 4 inch #CE32110G The Yates Bow Roller for Boat Trailers - TPR - 4 inch Long - 1/2 inch Shaft - Black…

view full answer...

Answer 8

There's no reason you couldn't install two of the CE Smith Self Centering Keel Rollers #CE29505 that you referenced. This would help center the boat as you pull it onto the trailer.

view full answer...

Answer 9

Both the CE Smith Keel Roller Assembly #CE32013G that you referenced and the similar #CE32003G use the same galvanized steel brackets. My contact at CE Smith confirmed that this is the only bracket they offer for their rollers. I have included a link…

view full answer...

Answer 10

To mount the CE Smith Panel Bracket for 12" Boat Trailer Rollers - Galvanized Steel #CE10305G you were looking at you have two options. The first being welding the bracket to your trailer. If you go this route you need to make sure to sand off…

view full answer...

Answer 11

As shown in the brief video and photo that I have prepared for you, the height of the rubber spool roller's center portion above the bottom of the frame on the CE Smith Spool Roller Assembly #CE10400G is 8-inches to the center of the roller and…

view full answer...

Answer 12

I went out to the warehouse and pulled CE Smith Spool Roller Assembly #CE10451G to measure it. It has an overall height of approximately 8-1/2 inches from the bottom of the bracket to the top of the roller. If you are talking about how far it would…

view full answer...

Distance From Outside of Roller to Outside of Plate For CE Smith Spool Roller Assembly CE10400G

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching