Replacement Pin and Clip for Andersen Ultimate Connection

Question

Question:

I have the Anderson No-sway WDH. I would like to purchase an extra pin that goes under the Tension Triangle Plate. Anderson manual shows a part number 3430. I could not find it on your site, but saw AM3431. It is a bit longer and the diameter is the same. Do you have the Anderson 3430 or can the AM3431 be used in its place? Thank you.

asked by: Ray M

1

Helpful Expert Reply:

We do have the Andersen 3430 you are looking for. It is the Replacement Pin and Clip for Andersen Ultimate Connection 5th Wheel Trailer Hitch System # AM3430.

expert reply by: Scott S

1

Answer 1

To remove the old broken remote latch for your Andersen Ultimate Connection 5th Wheel Hitch #AM3200, you will need to loosen the nuts around the black handle to release pressure, then the round part connected at the funnel/ converter box can be…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Pin and Clip for Andersen Ultimate Connection

Product Page this Question was Asked From

Continue Researching