Trailer Hitch that Fits 2006 Chevy Silverado 3500HD with 44 inch Frame Width

Question

Question:

will bwhdrh25122 fit the frame that measures 44in od .2006 chev 3500 crew cab long bed drw 4x4. thank you

asked by: Russell H

0

Expert Reply:

The B and W hitch part # BWHDRH25122 that you referenced only fits the cab and chassis versions of your truck which have a narrower frame width than what you mentioned at 34 inches from outside to outside. So what you'd want is the part # BWHDRH25189 instead which is designed for the truck frame dimensions you have on your 2006 Chevy Silverado 3500HD.

expert reply by: Jameson C

0

Answer 1

In regards to the B&W Heavy-Duty Trailer Hitch Receiver part #BWHDRH25189, the distance from the flange to the top of the receiver tube is 3-1/8" and the distance from the rearmost mounting hole to the end of the receiver tube is…

view full answer...

Answer 2

I had our warehouse measure the Curt Trailer Hitch Receiver #C15703 you were looking at, and has an overall width of 40-5/8", overall length of 29". The distance between the vertical mounting holes is 14-1/2" center to…

view full answer...

Answer 3

It is, I went and measured the distance from the mounting flanges of a Curt Hitch part #C15703 to the cross tube that we have in stock and found that it measures right at 6 inches. I attached an install video for you to check out as well.

view full answer...

Answer 4

Yes, the Curt hitch part #C15312 that you referenced does fit your 2007 GMC Sierra Classic dually that has frame dimension of 42 inches from outside to outside on your truck frame.

view full answer...

Answer 5

Both of the Curt hitch receivers have the same bolt hole measurements. It's 9 inches from the first hole (Closest to the front of the truck) to the second hole and 5-1/2 inches from the second to the third. There's 39 inches across…

view full answer...

Answer 6

The #BWHDRH25122 has 35-5/8 inches between mounting holes like what you see in the picture I attached. Since you need larger than than let me know what vehicle you have and I can see which would be best fit.

view full answer...

Answer 7

The Curt Trailer Hitch Receiver part #C15400 and the Curt Trailer Hitch Receiver part #C15800 are the exact same trailer hitch save for one has a 2" receiver tube opening and the other a 2-1/2" receiver tube opening. The dimensional…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...