How Thick is the Replacement Tongue for Yakima Rack and Roll Trailer

Question

Question:

I purchased a used Rack and Roll trailer. The original tongue had been replaced with with a piece of 3/16 steel square tubing. What is the thickness of the etrailer tongue tubing?

asked by: David E

1

Helpful Expert Reply:

The Replacement Tongue for Yakima Rack and Roll Trailer # 8880204 is 3/16" thick. The overall dimensions are 69-5/8" long x 2" wide x 2" tall.

expert reply by: Robin H

1

Answer 1

We have the replacement 2" x 2" Rack and Roll Tongue #8880204 but if you're needing that inner piece on the Tongue Extension Kit #Y08109 then that's only available with the extension kit so you'll need the whole part number.

view full answer...

Answer 2

I checked with Yakima and they informed me that the length of the Replacement Tongue for Yakima Rack and Roll Trailer #8880204 is 69 inches.

view full answer...

Answer 3

You'll be pleased to hear the base of the: -Malone Crossbar Conversion Kit for Standard Utility Trailer #MPG475 measures 32" before the bar starts to curve upwards. I have also attached an image showing this measurement for you to check…

view full answer...

Answer 4

So the answer is yes, with your 2-1/2 inch receiver you will still be able to use the Thule T2 Pro XTR Bike Rack #TH83JV. You are correct, however, that the your standard hitch reducer sleeve isn't going to work, so what you will need instead is…

view full answer...

Answer 5

Thank you for the kind words. We are happy to help! First, there is the extension that will fit a 2-1/2 inch trailer hitch on your 2016 Ford F-450 if you are interested, the Titan extension #RP45292 can extend 24 to 34 inches. Ball mount #BM20 is one…

view full answer...

Answer 6

The Yakima Rack and Roll Trailer #Y08107 referenced in your question can be easily folded for storage in numerous positions, however the wheels themselves cannot fold flat. The wheels though can be easily removed along with folding the trailer to…

view full answer...

Answer 7

From the ground to the top of the crossbars when the the Yakima Rack and Roll Trailer, #Y08106, is level, it measures 22 inches. The Heavy Duty Shocks, #Y08110, is using the terms shocks as an all encompassing term that covers the shock itself and…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

How Thick is the Replacement Tongue for Yakima Rack and Roll Trailer

Product Page this Question was Asked From

Continue Researching