Is There a Front Hitch for Bikes On a Tiffin Open Road with Ford F-53 Chassis

Question

Question:

I have a 2012 Tiffin Open Road class A motor home on a Ford F53 chassis. I would like to install a front hitch to haul our bicycles. Will this hitch, 65049, fit on my mh? If not, is there a hitch that will fit my mh? Thanks,

asked by: Mark F

1

Helpful Expert Reply:

The best option for carrying bikes on a Tiffin Open Road with Ford F-53 Chassis is on the rear hitch as there are no front mount trailer hitches for this application. If you're already using the rear hitch for towing then you can simply use a dual hitch adapter like the Roadmaster Dual Hitch Receiver Adapter for Tow Bars part # RM-077-2.

expert reply by: Conner L

1

Answer 1

In a flat towing situation the use of an adapter like #RM-077-2 does NOT reduce the tongue weight capacity of the trailer hitch because there is very little tongue weight on it when flat towing a vehicle. So you can use this adapter to flat tow your…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hello Steve. I do have a good solution for you, but I cannot recommend using the Malone Adapter #MPG544. Since it is rated for towing only 4,000 lbs, your 8,000 lb towed vehicle would be double the max towing capacity. You are right about there being…

view full answer...

Answer 5

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 6

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 7

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Answer 8

As long as the flat tow wiring is wired in before the 4-Way #C93ZV and you connect the power for the converter directly to the battery it will work. I have seen several use Magnetic Lights #TL21RK which they will wire in on the main harness to have…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 11

This will depend on the hitch used and the height of the trailer coupler. You want the trailer to be as level as possible. We have a page on calculating hitch height and coupler height to help you find what ball mount would work best. Most light duty…

view full answer...