Use One Ballmount to Tow Multiple Trailers - a 1-7/8 Inch and a 2 Inch Diameter Trailer Ball

Question

Question:

i have a pop-up trailer with a 2 in. hitch and just bought a boat with 1 and7/8 in. hitch. can i use 1 hitch for both trailers without changing out receivers each time.

asked by: Brian P

0

Expert Reply:

I would like to clarify some terminology so that we are on the same page, the hitch is the part attached to your 2008 Chevy Uplander. Then the ball mount or drawbar is attached to the hitch receiver using a pin and clip, or locking mechanism. Then the ball mount is outfitted with the appropriate size trailer ball. The diameter of the trailer ball shank needs to be compatible with hole the ball mount and the diameter of the trailer ball needs to be compatible with the trailer coupler.

Since you said you already have the pop-up trailer that uses a 2 inch trailer trailer ball I am assuming that you already have a complete towing system for towing that trailer with your Chevy Uplander. You most likely already have an appropriate ballmount with the proper rise needed to tow your pop-up. If that is not the case please let me know and I can make additional recommendations for you. I have also included a link to a helpful FAQ article that demonstrates how to measure for the correct rise or drop ball mount to tow your trailer.

More than likely with the vehicle and 2 types of trailers that you mentioned the correct ball mount will most likely be in rise position for towing. I recommend using an interchangeable hitch ball system. This will give you the versatility to tow both of your trailers, minimize the need for additional ballmounts, and more cost effective than buying two separate ball mounts, and trailer ball for each size. If your current ball mount is compatible with a 3/4 diameter trailer ball shank then I recommend the # 800B, however if you need a 1inch diameter trailer ball shank then you would use the # 901B.

I have provided links to the parts listed above, videos of the products, and a few helpful articles for your reference.

expert reply by: Rachael H

0

Answer 1

If your trailer has a 2 inch coupler then you definitely need to go with a 2 inch ball. Even though 1/8 inches doesn't sound like very much, it is enough that your trailer could come uncoupled under the right conditions. I have attached a link to…

view full answer...

Answer 2

You will still be able to use the hands free lift gate feature on your 2021 Mazda CX-9 with the Curt Trailer Hitch Receiver #C13284 installed, but you will need to put your foot on either side of the receiver and move it in and out until you find the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

From a convenience standpoint, the #306-X7186 EcoHitch would probably be easier to live with, as you wouldn't need to remove the receiver when it's not being used but because there'd be a 10 inch height difference between the hitch and…

view full answer...

Answer 8

We do have installation instructions for the EcoHitch Invisi Trailer Hitch Receiver #306-X7186 and I have sent them to you in a separate email. As you mentioned in your question, there are 3 trailer hitches available for your 2012 Chevy Volt and they…

view full answer...

Answer 9

You could do that if you wish, you'll just want to make sure that the heat shield is NOT sandwiched between the hitch and the chassis of the vehicle at any point. We frequently hear from folks with concerns about the vehicle being harmed because…

view full answer...

Answer 10

The 4-Leaf Slipper Spring w/ Radius End for 2,000-lb Trailer Axles #e69SR should be compressed ~2" under a 1,000 lb load which would make the "F" measurement ~1 3/4" with the 1,000 lb load. This is based on a formula to find…

view full answer...

Answer 11

To choose a compatible hub assembly for any spindle the key is knowing the inner and outer bearing part numbers, or if they are not available, precise dimensions of the spindle at the points where the bearings and grease seal ride. These points on…

view full answer...

Answer 12

The dimensions of the Torklift Rubber Camper Bumpers #TLA7001 are 8" by 2-1/2" by 2".

view full answer...

Use One Ballmount to Tow Multiple Trailers - a 1-7/8 Inch and a 2 Inch Diameter Trailer Ball

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching