How to Select Hubs That Are Compatible with Trailer Spindle
Question:
I need 8 of each Hub Spindle with Bearings and castle nut and lugs for 10-inch 4 on 4 golf cart wheels Round easy lube spindle. Wheels are 205/50-10.
asked by: Emanuel
Expert Reply:
To choose a compatible hub assembly for any spindle the key is knowing the inner and outer bearing part numbers, or if they are not available, precise dimensions of the spindle at the points where the bearings and grease seal ride. These points on the spindle are noted on the diagram I linked for you. Once you know the bearings this will tell you which hubs will fit properly.
You also need to select hubs based on the weight load that will be put on them. It appears you have a fabricated cart that uses the hub to allow some sort of tank to rotate on it. Be sure to select a hub that can handle the weight you're putting on it.
Your photo appears to show a 5- or 6-lug idler hub. This may be due to distortion of the photo. In any case I have linked our main page for all EZ-Lube trailer idler hubs that fit 10-inch wheels.
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub
- EZ Lube
- Pre-Greased
- Standard
- L44649
- L44649
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 8 Inch Wheel
- 9 Inch Wheel
- 10 Inch Wheel
- 11 Inch Wheel
- 12 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: apubr~10
- Search Results: mj~1500b~dwl
- Shop: Stabilizer Jacks - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 2
- Shop: etrailer Boat Trailer Jack w/ 2 Wheels - Sidewind - Swivel - 10-3/8" Lift - Zinc - 1.5K
- Q&A: Spring Compression for the etrailer 4-Leaf Slipper Spring While Under a 1,000 lb Load
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Single-Axle Trailer Hanger Kit for 1-3/4" Slipper Springs - 1-1/2" Tall Front
- Search Results: hanger
- Shop: BTR E-Z Lube Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter
- Shop: Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 1-7/8" Ball - Bolt On - 2,000 lbs
- Shop: Rear Hanger for 1-3/4" Slipper Spring
- Video: Redline Trailer Suspension - Leaf Spring Suspension - APS3SE Review
- Q&A: What is the Difference Between Load Range C and D ST175/80D13 Trailer Tires
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Search Results: first responder
- Search Results: dexter 8 259
- Video: etrailer Trigger Latch Channel Tongue Trailer Coupler Review
- Video: Review of etrailer 4 Leaf Slipper Spring - e69SR
- Video: etrailer Camper Jack - Stabilizer Jack - TJ01RT-HD Review
- Video: Review of TruRyde Trailer Spindles - EZ Lube BTR Spindle - TRU44FR
- Video: Review of TruRyde Trailer Spindles - Standard Spindle - TRU59FR
- Video: etrailer Round Swivel Marine Jack with Dual Wheel Installation
- Search Results: slipper spring hanger
- Search Results: e69sr
- Q&A: Can Leaf Springs with a Lower Weight Rating Be Used to Ease Ride of PWC Trailer
- Q&A: Bolt Thread Size of Mounting Hardware for etrailer Round Swivel Marine Jack w/ Wheel
- Article: Most Popular Wheel Bearings
- Q&A: Replacement Hubs for 1997 FLOE Pro 100 Plus Snowmobile Trailer
- Q&A: 60 Inch Guide Ons for Boat Trailer With Rectangular Tube Frame
- Shop: Tailgate