Is There Way to Use Weight Distribution System with 3 inch Hitch

Question

Question:

I have a 12K husky weight distribution hitch for my toy hauler travel trailer. My F350 dually has a 3-inch receiver hitch. The hitch itself came with a 2 inch shank and have to use two reducers. Its causing the holes in the hitch to oblong. Do they sell a 3-in shank that would adapt to the husky weight distribution hitch?

asked by: Ryan K

0

Expert Reply:

At this time the biggest hitch size we have weight distribution shanks for is the 2-1/2 inch hitch size like the part # C17132. Which you would have to then use a 2-1/2 inch to 3 inch hitch reducer part # BWRHXA2183.

expert reply by: Jameson C

0

Answer 1

Blue Ox doesn't offer a 3 inch shank, nor do our other suppliers, which is unfortunate but the good news is that using a reducer sleeve like the B&W #BWRHXA2183 along with the 2-1/2 inch shank included with the Blue Ox #BXW2000 system…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Luis, for your 2018 Ford F-350 that doesn't have the OEM pucks you would want the B and W Turnoverball hitch part #BWGNRK1116 that is a confirmed fit for your truck. I really like the B and W gooseneck hitches as they are known to be the…

view full answer...

Answer 10

Thanks for the pictures! No, I am sorry Richard you can not. The B&W Continuum item #BW78FR only works with frames that are 5" and 6" tall. Instead, I recommend using the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...