Can Replacement Trailer Axle be 1/2 inch Longer than Other Axle on Tandem Trailer

Question

Question:

Hi, I need to replace an axle on a tandem trailer and the closest axle I can find is about 1inch longer from brake flange to brake flange outside measurement. All other measurements are the same, is this 1/2 difference on both sides going to make a difference or can I use the axle I found as a replacement?

asked by: Walter

0

Expert Reply:

It wouldn't be an issue. Having the one axle stick out just 1/2 inch further with the #T3584F-EZ-8974 than the other wouldn't cause any issues.

expert reply by: Jameson C

0

Answer 1

You may be able to replace your existing axle that has an 84 inch hub face length with one that has an 89 inch hub face length without a problem but it's going to be dependent on your existing spring center length. This is the distance from the…

view full answer...

Answer 2

You actually should shoot for 4-1/2" of clearance between the top of your tire and the bottom of the fender well. This accounts for flex in your suspension. Unless 2,280 lbs is the GVWR (gross vehicle weight rating) of your trailer then you need…

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 5

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 9

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Can Replacement Trailer Axle be 1/2 inch Longer than Other Axle on Tandem Trailer

Product Page this Question was Asked From

Continue Researching