Correct Steering Stabilizer for a 2002 Workhorse W-22 Chassis

Question

Question:

What mounting bracket is needed for stablizer? W22 workhorse

asked by: Mike G

1

Helpful Expert Reply:

I checked with Roadmaster and the correct Roadmaster Exact Center Steering Stabilizer for a 2002 Workhorse W-22 Chassis is part # RM32RR for GVWR's over 22K or part # RM88RR for GVWR's under 22K.

expert reply by: Conner L

1

Answer 1

For your 2008 Workhorse W22 motorhome what you'd want for a front sway bar and steering stabilizer is the Roadmaster Front Sway Bar and TruTrac Rod Kit part #RM-1259-106 which comes with the front bar and a TruTrac rod which acts as a…

view full answer...

Answer 2

The installation of a front anti-sway bar won't do much for your steering but a steering stabilizer will and that's what I recommend. The correct one for a 2003 Tiffin Allegro Motorhome on a Workhorse W20 Chassis is the Roadmaster…

view full answer...

Answer 3

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 8

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 9

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 10

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 11

We do have that exact lube with the Aqua Lube part #RM-400-011-30.

view full answer...

Answer 12

In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just let me…

view full answer...

Correct Steering Stabilizer for a 2002 Workhorse W-22 Chassis

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching