Do You Need To Put A Fuse In-Line When Installing A Roof Vent Fan.

Question

Question:

I’m installing a 7500K fan and would like to know what size of fuse to use a n the circuit? I’m talking about the 12 volt dc. Thank you

asked by: Kenny G

0

Expert Reply:

In general you do not need to install inline fuses with roof vents like the MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed - Smoke # MA00-07500K.

If you are doing a normal install there is no need for an in-line fuse. If you do however still want to use a fuse to be extra cautious a 5 AMP fuse will do the job you are looking for.

expert reply by: David B

0

Answer 1

The power draw of the MaxxFan Dome Plus Roof Vent part #MA00-03810B per the manufacturer is 2 amps. This is the max power draw with the fan and light run concurrently at the highest setting.

view full answer...

Answer 2

The correct replacement fuse for your MaxxFan Dome Plus Roof Vent w/ 12v Fan #MA00-03810B is a 5 amp GMA fast acting fuse.

view full answer...

Answer 3

I have a solution for you, but the Kwikee part number 909506000 has been discontinued by the manufacturer, which is why you're not seeing it. Also, the #LC379146 and #LC301702 would not be the correct parts, since they're for newer Kwikee…

view full answer...

Answer 4

The reverse light pin on a traditional 7-way trailer connector, like part #PK11893 or a factory connector if that's what you have on your 2018 Ram, is the center pin. Take a look at the picture I attached that shows all the pin functions. To add…

view full answer...

Answer 5

For your Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote #FV807350, I first recommend verifying that you have new, fresh batteries in your remote. If you've verified that your batteries are indeed new, and in working order, then I recommend to…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 9

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 10

The Dexter 8-427 hub is no longer available. Even looking through Dexter's site the only references to it are replacement bearings. You can use a wheel with a larger pilot hole as long as the wheel attaches to the hub using lug nuts and not…

view full answer...

Answer 11

I have a solution for you, but the main issue with puck style lights that mount to the surface of your RV ceiling or under cabinets, is that there aren't replacement bulbs available and they aren't really designed to have the bulbs replaced.…

view full answer...

Answer 12

We carry replacements that could integrate into your Dometic AC system, but before purchasing anything you'll need to remove the cover of your air distribution box under the unit you're wanting to replace and look for the wire harness that…

view full answer...