Air Helper Springs and Air Compressor for a 2022 Ram 2500 Limited

Question

Question:

I want to install the firestone 7500 lb air lift system and the associated compressor in a 2022 Ram 2500 limited. Will you please help me out making sure I right parts for my truck? Thanks.

asked by: John G

0

Expert Reply:

I would be happy to help you. For your 2022 Ram 2500 Limited you are going to need the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs - Rear Axle item # F2706. This is a confirmed fit for both the 2WD and 4WD models. It has the 7,500 lbs capacity you requested. I have linked an installation video on a 2018 Ram so you can see the install process.

For the compressor the Firestone Air Command II - Analog Gauge w/ Heavy Duty Compressor - Dual Function - 150 ps item # F2219 you were looking at would work great with those Air Helper Springs. This compressor lets you adjust your two air springs independently from the comfort of your Ram's cab. It allows you to level your truck from front to back. It also allows you to get side-to-side leveling of off-center loads by inflating each spring with a different amount of air.

expert reply by: Jerred H

0

Answer 1

We sure do! What you are needing is the MORryde cushioned pin box replacement for the Lippert Rhino, and the part number RPB77-FD-06 is for 18,000 lb to 21,000 lb trailers. The pin box you are looking for is the following: - MORryde Cushioned 5th…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 9

Generally speaking, the lube plate will need to cover the skid plate on the 5th wheel hitch. There are some pin boxes out there that will recommend a specific lube plate but most of the times this classification will be from the 5th wheel hitch…

view full answer...

Answer 10

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 11

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 12

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...