What is the Correct Steering Stabilizer for a 2002 Workhorse W22

Question

Question:

which bracket kit do I need for a 2002 workhorse w22 ?

asked by: Alecs

0

Expert Reply:

For the 2002 Workhorse W22 the correct Roadmaster steering stabilizer with mounting brackets is # RM-RBK13-RSSA. The mounting brackets alone are # RM-RBK13. I have included a link to our FAQ on stability control for heavy duty vehicles.

expert reply by: Michael H

0

Answer 1

The Roadmaster Steering Stabilizer part #RM-RBK13-RSSA does fit the W20, W22, and W24 Workhorse chassis like you asked about.

view full answer...

Answer 2

For your 2008 Workhorse W22 Chassis, I recommend the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes #RM-RBK13-RSSA. This system has a tempered steel spring that works when compressed to push back to center and…

view full answer...

Answer 3

The difference between the Roadmaster Reflex steering stabilizers is how they connect to the brackets that fit onto the RV. Take a look at the pictures I attached and you can see the difference between the ends of them. #RM-RSSA has eyes on both…

view full answer...

Answer 4

The installation of a front anti-sway bar won't do much for your steering but a steering stabilizer will and that's what I recommend. The correct one for a 2003 Tiffin Allegro Motorhome on a Workhorse W20 Chassis is the Roadmaster…

view full answer...

Answer 5

From the research I did it looks like your 2003 RV M6342LX Workhorse is a Dolphin built on the W22 chassis. For a front sway bar you would want the #RM-1259-106 and for the rear the #RM-1259-109.

view full answer...

Answer 6

For your 2008 Workhorse W22 motorhome what you'd want for a front sway bar and steering stabilizer is the Roadmaster Front Sway Bar and TruTrac Rod Kit part #RM-1259-106 which comes with the front bar and a TruTrac rod which acts as a steering…

view full answer...

Answer 7

The answer to your question is yes, the handling on your 2003 Winnebago Adventurer built on a Workhorse chassis will definitely improve with the TruTrac that fits your coach, with the correct fit being the following: - Roadmaster TruTrac Front-Axle…

view full answer...

Answer 8

For your 2007 Winnebago Sightseer on the W18 chassis, you'd want the Roadmaster #RM-1259-116 Front anti-sway bar/TruTrac Rod kit. The part you'd looked at is a fit for the W20, W22 and W24 chassis and wouldn't work on your W18. I've…

view full answer...

Answer 9

The front trac bar that comes in the Roadmaster Kit #RM-1259-106 that you referenced will do the same job as a steering stabilizer but won't be as effective. For the best of both worlds I recommend going with the front Anti-Sway Bar #RM-1259-105…

view full answer...

Answer 10

According to the original sales brochure I looked up, your 2005 Newmar Mountain Aire 3778 was built on the Workhorse W-24 chassis. The same brochure states that the overall length of your coach is 37 feet 5 inches. Given that information, you'd…

view full answer...

Answer 11

Yes! Probably the single best addition you can make to provide better handling in your RV would be to install a rear anti-sway bar. Helper springs treat the symptom but not the cause like an anti-sway bar would. There are 2 rear sway bar options for…

view full answer...

Answer 12

For front air bags that fit inside of the coil springs on your 2002 Workhorse P32 chassis you will need #AL81560. You can roll up these bags and insert them up from the bottom through the hole below the coil spring mounts that you have described. No…

view full answer...