Recommended Vehicle Wiring For Towing a Trailer With a 2022 Hyundai Palisade

Question

Question:

I am going to install your hitch on my 2022 Hyundai Palisade but I need some help to find the right wiring. What wiring will I need to tow my trailer properly?

asked by: Gary W

0

Expert Reply:

As you will be installing the etrailer Trailer Hitch Receiver # e95ZR on your 2022 Hyundai Palisade I recommend the Curt T-Connector Vehicle Wiring Harness # CU94FR. This will give you a 4-way flat connector that is needed for pulling most small trailers or using Auxiliary Lights # C53201 with any hitch mounted accessory that impairs the view of the tail lights on your Palisade. If all your trailer requires is a 4-way flat connector then you are done and only need the Curt Easy Mount Bracket # C58002 to secure the 4-way to your receiver tube.

If your trailer has electric brakes you will need a 7-way connector and brake controller. The Universal Installation Kit for Trailer Brake Controller # ETBC7 and Redarc Pigtail # RED69FR will allow for you to install a Redarc Tow-Pro Liberty Brake Controller # RED24FR. This brake contoller will allow you to have a brake controller with one of the smallest foot prints available. The main unit will mount behind the dash and the control knob can be mounted where it is out of the way and easy for you to access. You will only need the Curt Easy Mount Bracket # C58003 to secure the 7-way on your receiver.

expert reply by: Bud M

0

Answer 1

Your 2021 Hyundai Palisade has brake controller wiring that runs from the port under the dash back to the plug that the Curt 7-way kit part #C68JR plugs into. That is why this kit that fits your vehicle does not have any wiring that runs from the…

view full answer...

Answer 2

Yes, we do offer a plug-in 7-way for a 2022 Hyundai Palisade, the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package part #C68JR which is a plug-in fit.

view full answer...

Answer 3

The Curt Echo Wireless Trailer Brake Controller - 1 to 2 Axles - Proportional #C51180 shouldn't have any issue with off-road bumps. The brake controller has a lip that the spring loaded latch of your trailer connector attached to in order to hold…

view full answer...

Answer 4

That would be a really cool feature! But no the Curt Echo does not have ability to also interface with the BlueTooth connected center console of your 2019 Ram 1500. It will require you to have the phone out which you could use the Rear View Safety…

view full answer...

Answer 5

The Curt Echo Mobile Trailer Brake Controller - Wireless #C51180 will work with any factory integrated brake controller according to my contact at Curt. It will take priority away from the factory controller when you plug in the Echo so you will…

view full answer...

Answer 6

No, you shouldn't have to make any connections under the hood when installing a brake controller on your 2019 Chevy Colorado. You will need to do some splicing though with a traditional brake controller as the needed wires are already run towards…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It is very, very likely that the issue with no power to the 12 volt pin of the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector #C68JR is due to a fuse either having been blown or not inserted, so definitely…

view full answer...

Answer 9

What you can do to have a 7-way/4-way combo at the rear of your 2022 Hyundai Palisade is to start with the 7-way kit part #C68JR that you referenced and then instead use the 7-way/4-way socket part #30955 in place of the included 7-way and you'd…

view full answer...

Answer 10

Since the trailer you purchased has a coupler that requires a 2" hitch ball, you will need to either replace the 2-5/16" hitch ball on your current ball mount or purchase a separate ball mount with a 2" hitch ball when you need to tow…

view full answer...

Answer 11

The Convert-A-Ball Ball Mount for 2" Hitches - 8-3/4" Rise - 10" Drop - 8,000 lbs #AMSC10 you referenced measures the rise from the inside top of the receiver to the top of the hitch ball platform not the top of the hitch ball itself…

view full answer...

Answer 12

In most cases it's a bit safer to go on the slightly lower nose height setting instead of slightly higher since higher can sometimes cause sway. But if the vehicle is going to squat quite a bit from the weight of the trailer then the higher would…

view full answer...

Recommended Vehicle Wiring For Towing a Trailer With a 2022 Hyundai Palisade

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching