Can The Air Lift LoadLifter 7500XL # AL57531 Be Installed In A Lifted 2019 Ram 3500

Question

Question:

Will the air lift suspension kits fit on a vehicle with a lift kit installed?

asked by: David M

0

Expert Reply:

Yes, you can install the Air Lift LoadLifter 7500 XL Air Helper Springs - Rear Axle # AL57531 on your 2019 Ram 3500 even though it's lifted. Depending on the size of the lift you'll just need a spacer kit like one of the follow:

Air Lift Universal Air Spring Spacers for LoadLifter 5000 and 7500XL - 2" Lift - Qty 2 # AL52420.

Air Lift Universal Air Spring Spacers for LoadLifter 5000 and 7500XL - 4" Lift - Qty 2 # AL52440.

Air Lift Universal Air Spring Spacers for LoadLifter 5000 and 7500XL - 6" Lift - Qty 2 # AL52460.

Air Lift Angled Universal Air Spring Spacers for LoadLifter 5000 and 7500XL - 4" Lift - Qty 2 # AL49GV.

Air Lift Angled Universal Air Spring Spacers for LoadLifter 5000 and 7500XL - 6" Lift - Qty 2 # AL79GV.

expert reply by: Kevin C

0

Answer 1

Air springs are definitely the right way to go for your 2019 Ram 3500 since they can be adjusted to accommodate a wide range of loads. For your application I recommend going with the Air Lift LoadLifter 7500 XL Air Helper Springs #AL57531 since…

view full answer...

Answer 2

The Firestone Air Command II Xtreme Duty Compressor with Analog Gauge, Air Tank, item #F2549 will work perfectly with those airbags. This is a dual path compressor that allows you to monitor and control the air pressure from inside your 2018 Dodge…

view full answer...

Answer 3

What you mention is absolutely normal for an air suspension system like the #2615 Firestone Ride Rite. The recommended procedure is when you load heavy objects into the truck is to have the bags at about 10psi then load up the truck. Then, add air…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...