Outboard Fifth Wheel Rail Kit that Fits 2022 Ford F-350 without OEM Rail Kit

Question

Question:

Reese says this will work on a 2022 ford f350 without oem prep package, but etrailer says it wont, can you confirm this?

asked by: Luke

0

Expert Reply:

I checked with Reese and confirmed that the Reese Outboard Fifth Wheel Rail Kit part # RP56017-53 that you referenced does fit your 2022 Ford F-350 that does not have the OEM fifth wheel rail kit. This will work great on your truck.

expert reply by: Jameson C

0

Answer 1

The OEM location for the gooseneck ball hole in the bed of your 2020 Ford F-350 will be 45-1/2 inches forward from the rear edge of the truck bed. There would be a flat spot in the bed where the ball will install as well. I attached a picture that…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 6

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 7

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 8

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 9

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 10

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Answer 11

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 12

Yes, you are going to also need the Demco Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 when using the Demco Autoslide 5th Wheel Trailer Hitch w/ Slider #DM8550040 with your Road Armor pin box. For a suspension enhancement I…

view full answer...