Can The Dutton-Lainson DL11004 Winch Use A 25 Foot Long Strap?

Question

Question:

Will your worm gear reduction hand crank winch, Model #DL11004, accept a 25 foot strap, Model # DL24249 or are there other options? The winch description indicates it accepts only the 20 foot strap. Thank you!

asked by: Andy M

0

Expert Reply:

We are a little limited on what we have for worm gear winches, but if your application does not require the strap to be completely wound and can have 5 feet of excess hanging down/out, you can use the 25 foot strap # DL24249 with the Dutton-Lainson # DL11004. If you cannot, you will only be able to use the 20 foot # DL24242.

The only other hex drive winch we have with the worm gear will be the Dutton-Lainson # DL11011 that is designed to be used with wire rope. The 1/4" Diameter with Safety Hook # DL24100 will fit this nicely and get you the length you need, but this set up will only be rated up to 1,400 pounds of capacity.

expert reply by: Lazer S

0

Answer 1

I recommend going with the winch you mentioned, the Dutton-Lainson Worm Gear Hand Winch with Hex Drive Handle #DL11004. It would work perfectly for your application and can be operated manually or with a power drill like you wanted. It also works…

view full answer...

Answer 2

Pulling cars onto a trailer will undoubtedly require pulling the vehicle up an incline, which will add extra resistance to the equation. If you are pulling a rolling load, not dragging the car and no flat tires, up just a slight incline like a 3…

view full answer...

Answer 3

I do have a solution for you, however the Dutton-Lainson Hand Winch #DL11004 referenced in your question is actually designed for use with a polyester strap and not cable. For the Dutton-Lainson 2,000 pound hex gear hand winch that uses cable you…

view full answer...

Answer 4

The Dutton Lainson Hand Winch, model #DL15721 does not feature a free-wheel option. The handle can be turned counter clockwise to unwind the cable or strap. If the minimum operating weight (175 lbs) is not applied, the winch handle will become loose…

view full answer...

Answer 5

We have exactly what you are looking for! The Dutton-Lainson Worm Gear Hand Winch #DL11004 has a hex drive topwind handle that you can operate by hand while it sits on the floor of your trailer or with a drill and a 5/8" socket. I recommend…

view full answer...

Answer 6

You can use Dutton-Lainson Worm Gear Hand Winch with Hex Drive Handle - 2,000 lbs Item #DL11004 for your utility trailer. If you do I strongly recommend using a drill to reel in the line or let it out (worm gear winches do not have a free-spool mode)…

view full answer...

Answer 7

The capacity of the Dutton-Lainson Worm Gear Hand Winch #DL11004 that you referenced is 2,000 lbs so your 18 volt drill would easily be able to operate the winch to raise 2,000 lbs as long as you have a 5/8 inch socket.

view full answer...

Answer 8

Yes, the Fulton High-Performance Brake Winch part #F143100 will work with the Universal Hand Winch Right Angle Mounting Bracket part #DL24110. I went out to our warehouse and test fit the two products together to confirm this for you. I have attached…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 12

Since you have a Dometic AC unit the best option to replace it from Advent would be the part #ACDOM135 which was designed for this exact situation and would allow you an easy install since the electronics would plug right in.

view full answer...

Can The Dutton-Lainson DL11004 Winch Use A 25 Foot Long Strap?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching