Replacements Needed For A 2007 Lippert 4,400 Pound Trailer Axle

Question

Question:

I need the bearings and seals for Lippert 2007 4400lbs axle. Do you know the parts numbers? Thanks

asked by: Rob S

0

Expert Reply:

We definitely have the replacements needed for your Lippert 4,400 pound axle. For the bearings, we do have what you need separately, but as this is a fairly uncommon size axle, we do not have an inclusive package. I have the inner and outer bearings as well as the seal listed below.

Grease Seal - Double Lip - ID 1.719" / OD 2.565" # 58846
Replacement Trailer Hub Bearing # L68149 (inner)
Replacement Trailer Hub Bearing # LM67048 (outer)

expert reply by: Lazer S

0

Answer 1

Lippert's 4,400 lb axles like what you have use the same bearings as 3,500 lb axles so the correct replacement bearing kit is the following: - Bearing Kit #BK2-100

view full answer...

Answer 2

The 4,400 lb trailer axles use the same bearings and seals as 3,500 lb trailer axle so for this you can use the Bearing Kit for #84 Spindles part #BK2-100.

view full answer...

Answer 3

The Dexter 4,400 pound will need the same type of kit used for the 3,500 pound axle. You can find it here, Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles - 3,500 lb with #84 Spindle #BK2-100. I suggest getting some extra seals too because they…

view full answer...

Answer 4

The Lippert 4,400 lb axles use the same bearings and seals as a Lippert 3,500 lb axle so you can use the Bearing Kit for #84 Spindle part #BK2-100 which comes with bearings, races, and seals. It looks like the 85 number you have found in your part…

view full answer...

Answer 5

I have a set of leaf springs for your Lippert Axle they are 6-Leaf Double-Eye Spring for 4,500-lb Trailer Axles - 26" Long item #e27SR. You will want to measure the spacing on your mounting brackets to confirm compatibility. The length from…

view full answer...

Answer 6

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 7

There is a couple of way to determine which wheel bearings and grease seals you will be needed for a trailer axle. First, checking the numbers on the wheel bearings and seal will allow you to select the correct parts for your axle. However, in some…

view full answer...

Answer 8

The only recommendation I can make for you would be to remove your hub and current grease seal so that you can determine what you currently have either by measuring it or getting the number off it and then pick out the correct seal based on that…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Replacements Needed For A 2007 Lippert 4,400 Pound Trailer Axle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching