Bearing Kit for Lippert 4,400 lb Trailer Axle

Question

Question:

HI, do you know bearings and seals I need for a Lippert 4400lb axle model # 774025 Travel Traler Ibex 19QBS

asked by: Troy S

0

Expert Reply:

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part # BK2-100 which includes inner bearing # L68149, inner race # L68111, outer bearing # L44649, outer race # L44610, grease seal # 58846, a cotter pin and a tang washer.

expert reply by: Jameson C

0

Answer 1

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 2

The first thing you will need to check is if there is enough space around the existing tires to use the larger size. Based on the old size you have, 235/75-15 (which isn't a common trailer tire size) the tires are approximately 28.8 inches…

view full answer...

Answer 3

The standard six lug bolt pattern for trailer wheels is 6 on 5-1/2 inches. If you have a six lug bolt pattern this would be what you'd have. The pilot diameter wouldn't be an issue either as the 6 lug wheels use a large enough pilot diameter…

view full answer...

Answer 4

It is not uncommon for the shackle straps to flip once weight is lifted off the suspension but if they do so when you have a load bearing then this will not allow for proper load distribution or suspension travel. The cause of this issue is that the…

view full answer...

Answer 5

I attached a picture that shows the proper position of shackles and equalizers on trailer suspension. Sometimes the shackle will flip up but if you jack up the trailer by the axle that's got the shackle flipped you can usually get it to flip back…

view full answer...

Answer 6

The correct replacement gear pack for your Lippert slide out will depend on the size of the arms attached to your slide out: - 2" x 3" Slide Arms: Lippert Standard Slide-Out Gear Pack #LC140409 - 2-1/2" x 2-1/2" Slide Arms:…

view full answer...

Answer 7

The TruRyde Spindle Nut #165686 has an outer measurement of 1.45 inches. You will use a 1-1/2 inch socket on this castle nut or we usually use a channel lock for these installations. I've attached a video of an installation of a hub to assist.…

view full answer...

Answer 8

A tang washer like #5-101 or #5-71 has a tab to secure the castle nut on the spindle so that it cannot rotate or back off on the threads. If the tang washer tab (or a cotter pin) is still in place in the notch on the castle nut (as in the linked…

view full answer...

Answer 9

The standard 3,500 lb axle uses the Hub Bearing Kit #BK2-100 which is for a #84 spindle. If your axle is a 1990 or newer then you likely need these parts but if it's older then I'll need you to measure your spindle to make sure we can get you…

view full answer...

Answer 10

Dexter axles are the industry leader in terms of overall quality. They are made in the USA and if you look around online or talk to people in the RVing community they general consensus is the Dexter axles are just better made overall and will be more…

view full answer...

Answer 11

For your AL-KO T44 axles, the brake assemblies you need are the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 4.4K #K23-478-479 or the manual adjust #K23-462-463-00 along with spoon adjuster #W80630. The…

view full answer...

Answer 12

You can use an RJ11 cable with the #MA59FR but some of the functions might not work properly. We've found that sometimes some of the functions will work backwards. What your best option would be is the communication cable part #MA69FR.

view full answer...

Bearing Kit for Lippert 4,400 lb Trailer Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching