Recommended Cover For A Coleman Mach 8 - Model # 47203B679 RV Air Conditioner

Question

Question:

Do you have a recommendation for a cover for a Coleman Mach 8 Plus air conditioner? It is a model 47203B679.

asked by: James B

0

Expert Reply:

The dimensions I'm seeing for your Coleman Mach 8 Model #47203B679 RV air conditioner show it being 28.40" W x 41.10" L x 8.25" T so the Adco RV Air Conditioner Cover for Coleman Mach I, Mach II, and Mach III TSR - Vinyl - Polar White # 290-3023 is going to be a great fit. This heavy-duty vinyl cover protects your RV's rooftop air conditioner from leaves, dirt, and the elements. The drawstring cinches the cover around the AC for secure fit and maximum protection. This cover also comes with a 3-year manufacturer warranty.

expert reply by: Kevin C

0

Answer 1

For the Adco cover #290-3023 would fit and work well.

view full answer...

Answer 2

Based on what you said the Adco #290-3023 will be the correct cover as this basically fits all of the Colemen Mach AC units. I attached an install video for the cover as well.

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 7

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although I'm…

view full answer...

Answer 8

Hey Jaime, yes you can replace your 25-1/4 inch 3,500 lb axle leaf springs with a 5k rated axle spring like the part #e44SR. This will increase the suspension's weight capacity and might make the ride quality a little rougher but it would fit and…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 12

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Recommended Cover For A Coleman Mach 8 - Model # 47203B679 RV Air Conditioner

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching