recommended Scissor Jack Replacement For A 2016 Keystone Passport Ultra Lite Grand Touring 2510RB

Question

Question:

I need to replace a scissor leveling jack on my 2016 passport ultralight grand touring 2510RB. I don’t no what jack to purchase as far as weight rating no information on old jack.

asked by: Mr S

1

Helpful Expert Reply:

We have a few different options for your 2016 Keystone Passport Ultra Lite Grand Touring 2510RB Travel Trailer; you'll just need to measure the for the correct lift needed.

The Scissor Stabilizer Jacks w/ Handle 5,000lbs - Qty 2 # TJSCHD-24 has a 18-3/4" lift.

The Leveling Scissor Jack 5,000lbs # JSC-24-IND has a 24" lift.

The Leveling Scissor Jack 5,000lbs # JSC-30-IND has a 30" lift.

expert reply by: Kevin C

1

Answer 1

A set of scissor jacks, one placed on each side of your trailer, will do a great job of reducing side to side movement and roll when the trailer is parked. You will just want to make sure the wheels are blocked so when the jacks are down the trailer…

view full answer...

Answer 2

As the jacks are raised an lowered, the upper mounting plate are designed to remain level. As you can see from the photo I edited, the ends of the jack uprights have gears or teeth built into them so that the mounting plate remains level. The…

view full answer...

Answer 3

For your 30 foot 5th wheel I really like the frame mount skid wheels that can swivel. For that the Ultra Fab kit part #UF48-979011 would be your best option. I attached a picture that shows these attached to a trailer frame as well. These don't…

view full answer...

Answer 4

Yes, you can use the Ultra-Fab Skid Wheels for Low-Profile RV's #UF48-979011 on your 2016 Heartland Sundance 278TS. These wheels are designed to mount to the RV's frame to help preventing dragging and digging of the trailer. Ultra-Fab…

view full answer...

Answer 5

While we do not carry a specific V-drag weld-on bar that protects your trailer from bottoming out, we do have an option that serves the same purpose. From the specs I have on your 2010 Forest River Cherokee Grey Wolf travel trailer, it measures 29.25…

view full answer...

Answer 6

The Skid Wheels part #UF48-979011 don't have weight capacities, but instead have trailer length recommendations. This kit is designed for up to 30 foot trailer so based on that this would be what you need.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...