Pro Series Round Replacement A-Frame Jack with 3 inch Standard Mounting Holes

Question

Question:

I need a replacement A frame jack for a light weight trailer 1500 lb. The mounting bolts have a triangular mount pattern, 3 inch on center. How can I find a compatible lift? Thanks

asked by: Paul K

0

Expert Reply:

I would be happy to help you find a replacement A-frame jack. I recommend the Pro Series Round, A-Frame Jack w/ Removable Footplate item # PSEA2000-14007. This standard A-frame jack has a 2,000 lbs capacity, 14" lift, features an 8" retracted height, and measures 11" from the mounting bracket to the top. The standard mounting bolt pattern on A-frame jacks is 3" on center. I have attached a picture of what the mounting bracket looks like on the Pro Series item # PSEA2000-14007. As you can see the holes are slotted to allow for some extra spacing.

expert reply by: Jerred H

0

a-frame jack holes
(click to enlarge)

Answer 1

The Dutton-Lainson A-Frame Trailer Jack, #DL22772 has an outer tube diameter of 2-1/4 inches. It measures 10 inches from the top of the bracket to the top of the jack. It measures 10-1/4 inches from the bottom of the bracket to the bottom of the tube…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...