What is Bolt Pattern of Trailer Brake Assemblies 23-180-181

Question

Question:

What is the measurement center to center on the holes in the mounting plate?

asked by: Gary W

1

Helpful Expert Reply:

I attached a picture that shows the bolt pattern of the trailer brake assembly part # 23-180-181 that you referenced.

expert reply by: Jameson C

1

trailer brake assembly 5 bolt pattern
(click to enlarge)

Answer 1

According to Dexter, the torque should be between 25-50 ft. lbs. when installing the #23-180-181. If you don't already have mounting hardware you'll need the Mounting Bolts and Hardware for 12" Brake Assemblies #BRKH12.

view full answer...

Answer 2

The difference between the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7,000 lbs #23-180-181 and the #23-105-106 you mentioned are the strength of the brake magnets. The #23-180-181 was designed for 7000lb axles…

view full answer...

Answer 3

I would be happy to recommend the correct replacement electric trailer brakes for you, but the 3175030707 did not cross reference to any brake assemblies. To determine the correct brake assemblies I would need to know the weight rating of your axle…

view full answer...

Answer 4

The only difference between the Dexter Electric Trailer Brake Kit part #23-180-181 and Dexter Nev-R-Adjust Electric Trailer Brake Kit part #23-464-465 is that the latter is self-adjusting which means the pads will automatically adjust for the best…

view full answer...

Answer 5

In order to power the Dexter Electric Trailer Brake Kit part #23-180-181 you'll want to run the 10 Gauge Primary Wire part #10-1-1 (Sold by Foot). In order to make the connections I recommend the Deka Heat Shrink Butt Connectors part #DW05745-5.

view full answer...

Answer 6

It looks like the Dexter axle part #60826 is a 7,000 lbs capacity axle. To replace the brake assemblies, I recommend the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7,000 lbs item #23-180-181. You will need one set…

view full answer...

Answer 7

It sounds like you are looking for 2 sets of left/right side brakes for your 7k trailer. If that is the case, we unfortuantely do not carry the 23-181-00 because these are an older brake model that was discontinued from Dexter. However, the new…

view full answer...

Answer 8

I'd set aside about two hours or so to do a brake assembly install like with the Dexter Trailer Brake Kit part #23-180-181 if it's your first time doing so. It's not a hard process but if you wanted to take your time with it I am sure two…

view full answer...

Answer 9

What you describe for your brakes after adjustment is not normal. You should have a slight drag on your brakes when spinning the hubs by hand when they are adjusted properly. There shouldn't be any difference when rotated in the opposite…

view full answer...

Answer 10

If the drums look like they are in good shape you don't have to turn them when replacing the assemblies. Take a look at the inside of the drum and if you don't see any grooving or obvious signs of wear they don't have to be replaced.…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The brakes you mentioned are for 7,000 lb axles and are 12-inch assemblies, similar to the Dexter Electric Trailer Brake Kit #23-180-181, but that is just one part of the equation in regard to determining the correct hub and drum. In order to…

view full answer...

What is Bolt Pattern of Trailer Brake Assemblies 23-180-181

Product Page this Question was Asked From

Continue Researching