Is the Streamline LED Trailer Third Brake Light # STL80RB Sold By Itself or a Pair

Question

Question:

D the long thin LED trailer lights for example: STL80RB come in pairs or singles. Does my money get me two units or just one?

asked by: Don B

0

Expert Reply:

The LED Trailer Third Brake Light, # STL80RB, is sold in quantities of 1. We also have # STL79RB which is more cost effective but is a 3-function light as opposed to a 1-function. I have linked a video review for you.

expert reply by: Michael H

0

Answer 1

To wire in a multi-diode 3rd brake light such as the 9-diode Optronics Thinline #STL59RB you will be better off using converter #118158. Pacer Performance 3rd Brake Light Logic Module #PP20-702 is for a single-LED light. Since you want only the brake…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 8

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels, #ORJW350D has an overall length of 18".

view full answer...

Is the Streamline LED Trailer Third Brake Light # STL80RB Sold By Itself or a Pair

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching