Availability Of Trailer Hitch Receiver For 2022 BMW X3 M40i

Question

Question:

Are there any options for this vehicle? 2022 BMW X3 M40i.

asked by: James L

0

Expert Reply:

There sure is!

For your 2022 BMW X3 M40i you will need to go with the Draw-Tite Trailer Hitch Receiver # 76226 as it is compatible with your M40i model where the # C13387 you were looking at is not.

This hitch is a great choice for your vehicle as its hidden crosstube design makes it so only the receiver itself is visible once installed as you can see in the included picture.

It looks like you were looking at towing accessories so if you will be towing a trailer with your X3 you will also need to pick up a vehicle wiring harness # TK77FR, and a ball mount, hitch ball, and hitch pin and clip. The ball mount will be dependent on your specific trailer so I have included a link to a helpful article that goes over how to measure for the correct ball mount, and a link to our selection of ball mounts compatible with this hitch for you to take a look at.

I included a video of the # 76226 being installed on a similar 2021 BMW X3 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The Curt Trailer Hitch Receiver #C13387 comes with everything needed to install on your 2019 BMW X3. If you are planning on towing with your vehicle, you will need a trailer wiring harness made for your vehicle. I recommend the Tekonsha T-One Vehicle…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Availability Of Trailer Hitch Receiver For 2022 BMW X3 M40i

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching