What Are the Dimensions of the Pollack 12801 2-Pole Socket Connector

Question

Question:

What are the overall dimensions of the bulkhead plug. Side to side and top to bottom, and cut out dimension needed. Planning where to put it on a 2022 F350 with 5th wheel package. Thanks

asked by: Keith

0

Expert Reply:

The # PK12801 has the following dimensions:

Top to Bottom: 3-5/8"
Side to side: 3-3/4"
Cut out: 1-13/16"

I've also added a diagram with these dimensions for you to check out.

expert reply by: Erik B

0

Pollack 12801 Dimensions
(click to enlarge)

Answer 1

The Buyer's Products connector, part #337TC2002, does need the wires to be soldered in the brass fittings. Also, I verified with Buyer's that it's designed for 6 gauge wire so you may not be able to get your 10 gauge to work. You might be…

view full answer...

Answer 2

The 2-Pole Socket Connector - Vehicle Side, #PK12801, will accept 4 or 6 gauge wire so it should be no problem for your application. If you also need a mounting bracket, use #PK11771. For the matching trailer end connector, if needed, use #PK12800.

view full answer...

Answer 3

The #PK11851 Single Pole Round Pin Trailer Connector is designed to deliver power to a trailer. It is not grounded, as the battery on the tow vehicle is already grounded and trailer mounted equipment is typically grounded as well. The ground…

view full answer...

Answer 4

The #PK11851 Single Pole Round Pin Trailer Connector is designed to deliver power to a trailer. It's not grounded, because the battery on the tow vehicle is already grounded and trailer mounted equipment is usually grounded as well. The ground…

view full answer...

Answer 5

On the 2-pole connector #PK12800 there is a set screw on the bottom, face end, of the connector. Remove this small screw with a flat screwdriver and you can pull out the terminals of the connector. On the other end you would route your wires (make…

view full answer...

Answer 6

A 2 gauge wire is only a little smaller than double aught (2/0) by about 0.11 inches diameter so it could be used in connector #PK11852. But I advise soldering in the wire and not crimping it for the best results. Triple aught (3/0) would be too…

view full answer...

Answer 7

The only option we can offer to run a large gauge wire between the trailer and tow vehicle is with the Pollak Single-Pole, Round Pin Trailer Wiring Socket part #PK11851 and the Pollak Single-Pole, Round Pin Trailer Wiring Connector part #PK11852. The…

view full answer...

Answer 8

The part #PK11852 and #PK11851 can be used for charging a trailer's battery. You would not be completing a circuit on the trailer since it's running to a battery so all you'd need to do is run the charge wire to the battery and you'd…

view full answer...

Answer 9

Yes, you will need to run a separate ground wire with the main power wire. So it would be best to use the Pollak 2-Pole Socket Connector #PK12801 with their 2-Pole Trailer Wiring Connector #PK12800 for your power wires. The physical connection from…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What Are the Dimensions of the Pollack 12801 2-Pole Socket Connector

Product Page this Question was Asked From

Continue Researching