Can the Mighty Cord 7-Way RV Style Trailer Connector Be Trimmed

Question

Question:

Can you cut this down to 7?

asked by: Gena M

0

Expert Reply:

Yes, you can trim the Mighty Cord 7-Way RV Style Trailer Connector part # A10-7W8 down to your specific length. If you have a set of heavy duty snips you can simply cut the cord at once but if not you'll need to use a razor to remove a section of the jacket and then snip each wire individually.

expert reply by: Conner L

0

Answer 1

The diagram you attached shows a 7-way wired up in what is considered the "traditional way." If you check out the chart I attached you will see the three ways (really only 2), that a 7-way can be wired. The Featherlite is wired up like the…

view full answer...

Answer 2

In regards to replacing a trailer connector on a trailer with an option like the Mighty Cord 7-Way RV Style Trailer Connector w/ Molded Cable part #A10-7W8, you need to match wires by function not color. In other words, if there is a green wire on…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 6

The first and easiest thing you should check is that the trailer is being towed level. If the trailer is nose high or low that can cause the equalizers to not sit level. You will need to select the correct rise/drop ball mount so that the trailer…

view full answer...

Answer 7

Shackle links can flip when the trailer is unloaded since there isn't enough weight to keep them in proper position, and while a new, shorter equalizer may help, the easiest thing to check is the shackle links. Shackles that are too short can…

view full answer...

Answer 8

If you just need the gearbox, the linkage will have an A, B, or C. Once you know which one you have, then you will need one of the following: Lippert Components Kwikee Step Gear/Linkage with A #LC379160 Lippert Components Kwikee Step Gear/Linkage…

view full answer...

Answer 9

Yes, for 5,200 standard trailer axles we have the hub part #8-219-4UC3-EZ which is a fit for 5,200 lb axles and has the bolt pattern of 8 on 6-1/2 inches like you said you need.

view full answer...

Answer 10

The correct replacement circuit and control board for your Lippert Electronic leveling system is the Replacement Control Panel for Lippert Ground Control 3.0 and Travel Trailer RV Leveling System #LC421484. This will be a plug and play solution, so…

view full answer...

Answer 11

I have included a link to a video on adjusting self-adjusting brakes. Basically there is a device on the adjustment wheel on these brakes that prevents the shoes from adjusting back inward. You have to sort of move that out of the way to be able to…

view full answer...

Answer 12

According to my research, the correct replacement head for your Reese 113066 is the Replacement Head for Reese Weight Distribution System #RP58167.

view full answer...

Can the Mighty Cord 7-Way RV Style Trailer Connector Be Trimmed

Product Page this Question was Asked From

Continue Researching