Inner Dimensions of the Flint Hill Goods Wheelchair Carrier # FHG77Z With Ramp in Vertical Position

Question

Question:

Can you tell me what the inside dimensions are for the FHG77ZR with the ramp in the vertical position?

asked by: Gordon

1

Helpful Expert Reply:

I spoke with my contact at Flint Hill Goods and found that the inner dimensions of the Flint Hill Goods 30" x 50" Wheelchair Carrier w/ 48" Ramp - 2" Hitch # FHG77ZR, is 48" long x 28" wide x 5" deep with the ramp in the vertical position.

expert reply by: John H

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The Flint Hill Goods 30" x 50" Wheelchair Carrier w/ 60" Ramp #FHG99ZR weighs about 42 lbs.

view full answer...

Answer 8

That is a keen observation and a good question. I actually had the chance to assist with assembly of one of the Flint Hill Goods 30" x 50" Wheelchair Carriers #FHG99ZR not too long ago. The main bolt for the shank is indeed quite large, so…

view full answer...

Answer 9

The ride on the back of a trailer is very rough due to the extended distance from the axle so a lot of hitch mounted accessories like the Flint Hill Goods 30x50 Wheelchair Carrier part #FHG99ZR are not rated for this. Instead, I recommend using the…

view full answer...

Answer 10

I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a service body truck like yours are multi-fit hitches like the #41990 that has a 16k capacity. This is a weld on hitch that would require either the 7…

view full answer...

Answer 11

I'm not sure which coupler that is, but I can say that a certain amount of rattling is to be expected because of the space needed to allow the ball to turn inside the coupler-especially with an adjustable coupler. With that being said, you can…

view full answer...

Answer 12

The problem you are experiencing is pretty common for vehicles that have seen a couple winters. What happens is the weld nuts get a bit of corrosion in them and that prevents the bolts from being able to thread. This makes it seem like the nuts are…

view full answer...

Inner Dimensions of the Flint Hill Goods Wheelchair Carrier # FHG77Z With Ramp in Vertical Position

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching