Rear Sway Bar for 2003 Workhorse W22

Question

Question:

I have been researching rear sway bars for my 37’ w22 motorhome. I know the ideal sway bar should be 1 3/4” but I am told they are out of stock and will not be available for some time. I currently have sumo springs. New shocks, front and rear track bars and front sway bar. Would you recommend my using your 1 1/2” roadmaster rear sway since it is in stock?

asked by: Nils

0

Expert Reply:

For your 2003 Workhorse W22 the recommended rear sway bar is the part # RM-1259-108 which is a 1-1/2 inch diameter bar. This will work great and would not be a compromise in any way.

expert reply by: Jameson C

0

Answer 1

The Roadmaster Rear Anti-Sway Bar part #RM-1259-109 is a bolt-on component that does not require the rear wheels to be removed. Please note the linked installation instructions for you to review.

view full answer...

Answer 2

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 3

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The air suspension system on your 2022 Ram 2500 limits your options for suspension enhancement. None of the air bags made for your truck will be compatible. Instead, I recommend adding the SumoSprings Rebel Custom Helper Springs #SS64VR. The…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

We do - for your 2023 Ford F-350 you'll want the TorkLift StableLoad Suspension Upgrade w Quick-Disconnect #TL89CR.

view full answer...

Answer 10

In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just let me…

view full answer...

Answer 11

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 12

Hi there David; we do have truck camper jacks that can work for your F-250 with a lift and large tires. What you can use are camper jacks from Brophy, which have a 17" to 67" lift range, which is the highest possible lift height. There are…

view full answer...

Rear Sway Bar for 2003 Workhorse W22

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching