Is Additional Regulator Needed for MB Sturgis Sturgi-Stay # 103539-MBS

Question

Question:

with the extended stay kit do I need a regulator on the 100 lb tank ,I am plumbed into the rv regulator but im wondering about excess pressure on the long hose

asked by: Michael P

0

Expert Reply:

With the MB Sturgis Sturgi-Stay T-Fitting w/ Hoses for POL Valve, # 103539-MBS no additional regulator is needed, it has all you need with it.

expert reply by: Michael R

0

Answer 1

The MB Sturgis High Capacity Two-Stage Auto Changeover Regulator #888001-MBS reaches upwards of 500,000 Btu P/H and maintains pressure of 9 WC or above. This sounds like what you are seeking as the Compact Low Pressure 2-Stage Automatic Changeover RV…

view full answer...

Answer 2

Chaining 4 tanks together is not recommended. I instead would use two separate systems an you will want to make sure the two additional tanks can also sit upright and have proper ventilation. You can use base #37207-31535 for both or #CAM57236 for…

view full answer...

Answer 3

The kit we offer that is designed for connecting an RV propane tank with an auxiliary tank is the MB Sturgis Quick Disconnect Deluxe Sturgi-Stay Propane Adapter Kit #103539-MBS which is designed for exactly what you are describing.

view full answer...

Answer 4

The MB Sturgis Sturgi-Stay T-Fitting Kit #103539-MBS allows you to connect an auxiliary propane cylinder to power appliances so that you do not deplete the on-board gas supply in your RV's tank. The kit installs without tools and with no…

view full answer...

Answer 5

There are several methods to try and determine the amount of liquid propane remaining in a tank. The first is a pressure gauge like the Camco #CAM59023. This reads the pressure of vapor propane which remains steady until mostly empty then the needle…

view full answer...

Answer 6

To add a 100 lb tank to your two 30 lb tanks, I recommend the MB Sturgis Sturgi-Stay T-Fitting w Hose - Type 1 Valve - Quick Disconnect, Disposable Cylinder Ports #103615. This will allow you to connect the red fitting to one of your tanks and the…

view full answer...

Answer 7

Yes, the #100019-24 pigtail can be used to connect your dual-cylinder 100 lb propane setup to the regulator on your RV. Since this hose does not have a back-check to contain a gas leak, you will need the #204120-MBS fitting that includes a…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...