Will the Curt 14055 or the Draw-Tite 41945 Extend Past the Bumper Further on an 06 E-350?
Question:
I have a 2006 e350 Super Duty Extended Van It has a rear bumper with a place for a ball but I need a hitch that sticks out close to even with the bottom others bumper. Comparing hitches 41945 and 14055 Wich both show no drilling, which one sticks out further or do you have a better recommendation? I need at least 10000 tow and 12000 distributed or better with as much tongue weight capacity.
asked by: Chuck
Expert Reply:
The Curt # 14055 will actually sit just about flush with the edge of the bumper once installed on your 2006 Ford E-350. Though this will meet the weight capacities you need, if you are looking for something to completely clear the bumper, it will fall a little short. No pun intended.
On the other hand, once the Draw-Tite # 41945 is installed, the center of the hitch pin hole will extend out 1-1/2 inches from the edge of the bumper. This is also the highest rated hitch we have available for your vehicle and if you needed the extra length at the end of the hitch, it will definitely be my recommendation.
Products Referenced in This Question
Draw-Tite Ultra Frame Trailer Hitch Receiver w/ Cast Center - Custom Fit - Class V - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class V
- 1500 lbs TW
- 10000 lbs GTW
- 12000 lbs WD GTW
- 2 Inch Hitch
- 1200 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 1000 lbs TW
- 10000 lbs GTW
- 12000 lbs WD GTW
- 2 Inch Hitch
- 1200 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Front Mount Hitch
- Search Results: 75703
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Q&A: Hitch Recommendation for a 2006 Ford E350 Cutaway
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Choosing the Right Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Installing 7-Way Trailer Connector on 2014 Ford E-350 Van
- Video: etrailer Hitch Pin Alignment Collar Review
- Article: How to Measure for Trailer Hitch Drop
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Brake Controller
- Search Results: hitch
- Q&A: Installing 7-Way Trailer Connector on 2005 Ford E-150 Van
- Video: Choosing the Right Brake Controller
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Search Results: brake controller
- Article: My Trailer Hitch Doesn't Fit
- Shop: Suspension Enhancement
- Search Results: trailer brake controller
- Video: Draw-Tite Front Mount Trailer Hitch Installation - 2016 Ford E-Series Cutaway
- Q&A: What Roof Boxes Will Fit On The Rhino Rack HD Square Crossbars
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Trailer Wiring Diagrams
on Trailer Hitch
