Does Draw Tite Hitch 75703 Fit with Full Sized Spare

Question

Question:

Will 75703 hitch will clear a 245-75R16 spare tire for a 1998 ford club wagon xlt 5.4l?

asked by: Ron

1

Helpful Expert Reply:

Yes the Draw Tite hitch part # 75703 that you referenced will work with a full sized spare.

expert reply by: Jameson C

1

Hitch Installed with Spare
(click to enlarge)

Answer 1

The Draw-Tite Max-Frame Trailer Hitch Receiver #75703 is a great fit for your 1983 Ford Van without step bumper. I've attached a photo that shows the fit and no bumper contact. I've also attached a video to further assist. This hitch is a fit…

view full answer...

Answer 2

If the bolt holes are 38-5/8 inches from frame rail to frame rail on your 2008 Ford E350 the Draw Tite Hitch part #75703 will fit your cutaway model. I attached an install video for the hitch for you to check out as well.

view full answer...

Answer 3

I reached out to Draw-Tite and they told me the Draw-Tite Max-Frame Trailer Hitch Receiver #75703 was never tested on a 1991 Ford E-150 with the dual fuel tanks. This does not mean it will not fit, it means it has never been tried. I am attaching a…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Lisa, To flat tow your 2020 Jeep Grand Cherokee Trailhawk you'll need the Blue Ox Tow Bar Wiring Kit #BLU86XR. This wiring harness comes with connectors to plug inline with your factory tail light wiring. If you haven't picked out the…

view full answer...

Answer 6

Among the hitches offered for your 2008 Ford E-150 van, all shown on the linked page, the Draw-Tite Class V hitch #41945 will extend furthest to the vehicle's rear. In fact this hitch extends rearward past the bumper on the vehicle shown in the…

view full answer...

Answer 7

For your 2003 Ford E-350 with a step bumper, the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75703 will fit well. I've attached a photo of a step bumper fit to assist. I've also attached a video install of a…

view full answer...

Answer 8

The AL-KO company was bought out by Dexter, so he may have been thinking Dexter axles which the #K23-478-00 and #K23-479-00 would fit with the 4 bolt mounting pattern. The K23-538-00 and K23-539-00 are the correct ones for the AL-KO T-44 axle, as you…

view full answer...

Answer 9

I attached a picture that shows the Curt hitch part #C77VV installed on a Hornet to show you where the hitch opening will sit once installed. It does fit right to the bottom of the rear bumper.

view full answer...

Answer 10

The notches on this hitch #14053 are not designed to fit around the rivets. Rather the hitch flange will sit directly below the rivets. This hardware kit includes steel spacers which go between the frame and the hitch. These allow the hitch it be…

view full answer...

Answer 11

I have a solution for you that I can provide, but we aren't going to have a custom fit hitch to fit a vehicle like what you referenced. I spoke to my contacts at Curt and Reese and the only styles of hitches that can be made to fit a service body…

view full answer...

Answer 12

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...