Will the Draw-Tite Class III Hitch Fit a 1999 Chevy Silverado 1500

Question

Question:

I have a 99 Chevy Silverado 1500 4x4...my frame is 39 inches wide at the center of bolt holes...will this fit my truck

asked by: Jeff A

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver part # 75521 is indeed a confirmed fit for a 1999 Chevrolet Silverado 1500. It mounts to bolt holes 39" on center.

expert reply by: Conner L

0

Will the Draw-Tite Class III Hitch Fit a 1999 Chevy Silverado 1500
(click to enlarge)

Answer 1

The etrailer Trailer Hitch Receiver part #e98849 will be an excellent replacement hitch option for the factory hitch on a 2012 GMC Sierra 1500. It will provide a direct bolt-on swap with no drilling required. It's rated for up to 10,000 lbs which…

view full answer...

Answer 2

Good question, and there is just a single difference between the Curt and etrailer trailer hitches that fit your 2010 Chevy Silverado 1500, which is the finish. The Curt has a glossier finish than the matte black finish of the etrailer hitch, so you…

view full answer...

Answer 3

The main difference between a Class III hitch and a Class IV hitch is the capacities they set for the hitches. Class III hitches are rated for up to 6,000 lbs GTW with 600 lbs TW whereas a Class IV is rated for up to 12,000 lbs GTW and 1,000 TW. For…

view full answer...

Answer 4

The etrailer brand #e98849 is a fit for all trim levels of the 2008 Chevy Silverado 1500, including your LTZ. The hitch has a 6000 lb towing/600 lb tongue weight capacity or 10000 lb towing/1000 tongue weight if used with weight distribution. For a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Will the Draw-Tite Class III Hitch Fit a 1999 Chevy Silverado 1500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching