Recommended Bathroom Vent Fan To Replace Older Ventline V2045

Question

Question:

i am looking to by the whole unit how can i do this ?

asked by: Tom Q

0

Expert Reply:

I have a different option for you, but the Ventline Model V2045 Bathroom Vent Fan you have is no longer available.

The closest option we have is the MaxxFan Dome Plus Roof Vent w/ 12V Fan - LED Light - 6" Diameter - Manual Lift - White # MA00-03810W which fits 6-1/4" diameter and roofs that are between 1" - 6" thick.

I included a video of the # MA00-03810W for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The Replacement Fan Motor #BCD0390-00 referenced in your question is the correct motor for your Ventline V2045 model fan. I did also go out to our warehouse to take a look at the motor and measured a length of 1-1/2 inches for the exposed length on…

view full answer...

Answer 2

The V2044 fan has been discontinued for awhile, but the Ventline #BCD0390-00 would be the correct 110V-AC motor. I've confirmed that these are the proper replacements with my Ventline representative. For the fan blade the replacement for the…

view full answer...

Answer 3

The Ventline model V2065 Vent assembly is no longer available. If you are wanting/needing to replace the entire vent then your only option will be with a different model unit that closely matches the dimensions of the V2065. I recommend taking a look…

view full answer...

Answer 4

The Ventline V2044 Bathroom Ceiling Vent can use the Replacement 110-Volt AC Fan Motor for Ventline RV Bathroom Insert Fan w/100 CFM Capacity #BCD0314-00 or the Replacement Fan Motor for Ventline Exhaust Fan #BCD0390-00. We have confirmed with…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...