How Much Does the Curt Heavy Duty Forged Ball Mount with 2-5/16" Ball - 1" Rise Weigh

Question

Question:

How much does the part weigh with ball?

asked by: Tony

0

Expert Reply:

The Curt Heavy Duty Forged Ball Mount part # C45331 is purposely overbuilt with more material than normal which is how it is able to obtain higher than normal capacities. The side effect of this is that the ball mount will weigh more than others and this one comes in at around 15-16 lbs.

expert reply by: Conner L

0

Answer 1

Since the Curt ball mount part #C45331 has a 1-1/4 inch diameter ball hole you'd want a hitch ball like the part #A-90 which will fit and work great.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

That's weird, the 7-Way Vehicle Power Adapter for Furrion RV Observation Camera #FR87PR should allow you to use your camper at the same time as that's what it's designed for. If you want to just avoid the adapter all together, I would…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 9

The canister of the Pace Edwards UltraGroove Retractable Hard Tonneau Cover #PE57CV is 12" tall x 10-1/4" deep.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 12

It looks like for the HF650M you'll be needing the Replacement Prop Rod Assembly for Leer Tonneau Covers #LE54MR.

view full answer...

How Much Does the Curt Heavy Duty Forged Ball Mount with 2-5/16" Ball - 1" Rise Weigh

Product Page this Question was Asked From

Continue Researching