Replacement Prop Rods for a LEER HF650M Tonneau Cover

Question

Question:

Hi there, I need to replace the prop rod on my HF650 Leer Tonneau Cover and I’m having difficulty ing the correct product. I have a 2020 Chevy Silverado Trailboss with a 5’ 3/4” bed. The part number you have for that specific bed cover is #LE97FR My current rods measure 16.5” between the center of each socket end. Can you provide me with the correct prop rod part for this? Thank you Matt

asked by: Matthew T

0

Expert Reply:

It looks like for the HF650M you'll be needing the Replacement Prop Rod Assembly for Leer Tonneau Covers # LE54MR.

expert reply by: Bryce D

0

Answer 1

I assume you're talking about the prop rods on your LEER HF650M quad fold tonneau cover, in which you'll just need the Replacement Prop Rod Assembly for Leer Tonneau Covers #LE54MR. If you're talking about something different, let me know…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

Hey Jeff, The Pace Edwards JackRabbit Retractable Hard Tonneau Cover w Explorer Rails #311-JED7833 is designed for a 6-1/2' bed while the #311-KRD7936 is designed for an 8' bed. Since you have a 6-1/2' bed the #311-JED7833 would be the…

view full answer...

Answer 12

If you check out the attached picture you can see where you'll find the serial number and date code on your cover.

view full answer...

Replacement Prop Rods for a LEER HF650M Tonneau Cover

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching