Camera Setup for 2019 Palomino Puma that is Pre-Wired

Question

Question:

My 2019 palomino puma is wired for a backup camera. Do they make one that syncs to my 2020 Silverado 1500 Lt trail boss screen in my truck so I can use the factory radio screen when I am backing up to see behind my tt?

asked by: Mark A

0

Expert Reply:

I hope we eventually get a camera setup that will integrate into the screen in your truck but as or right now (August 2021) only solution for your Palomina Puma that is wire for a Furrion camera system is a setup that would require you to have a second monitor in your truck like the Furrion Vision S # FOS43TASF.

expert reply by: Jameson C

0

Answer 1

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 2

Yes, but there is only one system that will work on your Palomino Puma Travel Trailer, the Furrion Vision S Wireless RV Backup Camera System. This system is offered with a 4.3" monitor part #FOS43TASF or the 5" monitor part #FOS05TASF.…

view full answer...

Answer 3

The newer Chevrolet and GM pickup trucks have a known power deficiency issue with the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras #FCE48TASL-05. There is likely nothing wrong that you did, the problem is the…

view full answer...

Answer 4

The most likely cause of the "no signal" error you are receiving with the Furrion Vision S Wireless RV Backup Camera System part #FOS43TASF is due to an interruption on the camera's power wire. Make sure that the camera is receiving…

view full answer...

Answer 5

The Furrion camera system we have is a closed system and would not be compatible with the in-dash display so you would need to purchase GM's camera system to be able to connect to your display instead of having another monitor. If you do end up…

view full answer...

Answer 6

That's weird, the 7-Way Vehicle Power Adapter for Furrion RV Observation Camera #FR87PR should allow you to use your camper at the same time as that's what it's designed for. If you want to just avoid the adapter all together, I would…

view full answer...

Answer 7

We definitely know about the issue you are referring to. We have just the part for you! Furrion recently came out with a brand new adapter for your 2022 GMC Sierra 1500 Limited to work with your camera system. The part you need is the 7-Way Vehicle…

view full answer...

Answer 8

You can have more than one iPhone "connected" to the Lippert Tire Linc system part #LC37VR but only one can be used at a time. So basically you or your wife could have their phone connected but if you needed to switch between the two phones…

view full answer...

Answer 9

The pre-wiring of Furrion pre-wired RVs is basically just two wires as well as the Voyager harness like part #PSVCWVCMS130AP. One wire is the power wire which is the running light circuit and then the other is the ground so it really would just be a…

view full answer...

Answer 10

Yes, the 7-Way Vehicle Power Adapter #FR87PR will allow your Furrion camera system to operate correctly. Your 2023 Chevrolet Tahoe uses a Pulse Wave Modulation for the trailer lights to be able to detect errors with the trailer lighting. The adapter…

view full answer...

Answer 11

You're correct, the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision - Rear Mount - 4.3" Screen #FOS43TASF has been known to need the 7-Way Vehicle Power Adapter w/ Power Switch for Furrion RV Observation Camera Item #FR87PR…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...