What are Wheel Covers in Relation to Valve Stem Extensions

Question

Question:

Valve stems what are wheel covers

asked by: Tom

0

Expert Reply:

With valve stem extensions like the part # WM8001-135 that you referenced we have a few options based on how they attach. These attach to the hub whereas other options would clip to a wheel cover if there was one present. Not all wheels have wheel covers which it sounds like yours doesn't.

expert reply by: Jameson C

0

Answer 1

We have a Lippert Components replacement slide motor that will work with the Schwintek system. It is the Lippert In-Wall RV Slide-Out Motor #LC236575. It is a gear ratio of 300:1. This is the correct replacement for the Schwintek IG420294X00096R.

view full answer...

Answer 2

We have a Lippert Components replacement slide motor that will work with the Schwintek system. It is the Lippert In-Wall RV Slide-Out Motor #LC236575. It is a gear ratio of 300:1.

view full answer...

Answer 3

Would you be able to check your motor to see what kind of gear ratio it has and if it is a Lippert Components In-Wall Slide-Out? Unfortunately manufacturers don't keep public records of that kind of stuff so I wouldn't be able to tell you…

view full answer...

Answer 4

The Wheel Masters 4-Hose Inflation Kit - 16" to 19-1/2" Dually - Hub Mount - 135-Degree Bend #WM8001-135 would be the correct inflation kit for the dually setup of your Thor Freedom Elite. This will attach both of the valve stems to the…

view full answer...

Answer 5

While not required as it is a 5th wheel hitch, safety chains are always a good idea, including for the Curt CrossWing Lightweight 5th Wheel Trailer Hitch #C86JR. There are even specific chains and mounts for the CrossWing, the Curt Safety-Chain Loops…

view full answer...

Answer 6

Square axles normally don't have spring seats like a round axle but do have a hole for the leaf spring bolt to fit into. Take a look at the CE SMITH #CE33201GA-HUB for a visual. The U-bolt mounting kits will have a hole in the center for the…

view full answer...

Answer 7

If you'd be willing to cut off the Lance connectors and wire in 6-ways or 7-ways in place of them we can help, but at this time only Lance can get you that specific connector. You could use the part #A7WCB with the #PK12-707E and you'd have a…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

What are Wheel Covers in Relation to Valve Stem Extensions

Product Page this Question was Asked From

Continue Researching