What Mounting Hardware Is Included with the Curt Class I Trailer Hitch # C11265

Question

Question:

I would like to ask bolt size of mounting bolts for a trailer hitch fir an 09 Corolla xrs. Please.

asked by: Shawn

0

Expert Reply:

The required hardware for the Curt Class I Trailer Hitch, # C11265, is four M12-1.25 x 30mm Grade 8 hex bolts and four 1/2 inch conical toothed washers. Curt states that only their hardware should be used with this hitch because that is the only hardware that it has been tested with.

For a complete replacement hardware kit for this hitch, you can use part # RHK. I have attached a link to this product page for you. Once you are on the product page, simply enter the part number of your hitch and select the manufacturer (Curt). We will send you an entire replacement hardware kit for this hitch.

expert reply by: John H

0

Answer 1

You sure can order just the installation hardware for your Curt #C11265 hitch. Just type #RHK in the search box on our website. Then click on the photo and you will be on the product page. Type C11265 in the box under Hitch Item Number. Open the…

view full answer...

Answer 2

The M12-1.25 x 30mm Hex Bolts that come with the Curt #C11265 hitch for your 2010 Toyota Corolla are not a very common size, so they will not be available on their own, unfortunately. However, we do have the Replacement Hardware Kit #RHK that will…

view full answer...

Answer 3

The hardware that comes with the Curt hitch part #C11030 that you referenced is Grade 5 which means it is zinc coated to fight corrosion. Zinc coating isn't quite as corrosion resistant as stainless steel but it does a good job preventing rust.…

view full answer...

Answer 4

Yes, as long as the bike rack was Class I compatible the Curt hitch part #C11265 that you referenced can be used to carry a bike rack. For a bike rack I really like the very stable, easy to load, and overall well-built Hollywood Racks Trail Rider…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

What Mounting Hardware Is Included with the Curt Class I Trailer Hitch # C11265

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching