Can The Tension Be Adjusted On The Lippert Thin Shade

Question

Question:

I need to adjust the cords so that my shades will stay put and operate correctly, but Im afraid of breaking the plastic levers when I try to move them. How can I make them move easier? Thank you.

asked by: Marilyn

0

Expert Reply:

According to Lippert there are no cords for the Lippert Thin Shade Item # LC806621. The shade actually slides inside of a track. What you can tray doing is open the shade all the way and try to wipe out the tracks.

expert reply by: Shane H

0

Answer 1

I confirmed with Progressive Dynamics that the replacement part you need is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp #PD4645V.

view full answer...

Answer 2

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5…

view full answer...

Answer 3

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 4

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

The Replacement Crank Extension for Lippert Components Spare Tire Winch Assemblies #LC1315411, which is a replacement for Lippert Components Spare Tire Winch with Offset Cable #LC159056, has an inside diameter of 0.50 inches and the hex has a 0.75…

view full answer...

Answer 10

There are going to be two parts to the handle that you will need to operate the Lippert Components Spare Tire Winch part #LC159056. The first of which is the intermediate shaft or what Lippert calls a Crank Extension part #LC1315411. This will be…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

I was able to find the OEM part number for the Chevy spare tire hoist but I was unable to find a weight capacity rating on it. The owner's manual for the 2015 Chevy Silverado 1500 and the original hoist can handle the weight of a full sized spare…

view full answer...

Can The Tension Be Adjusted On The Lippert Thin Shade

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching