Recommended Idler Hubs Compatible with the Kodiak 12" Disc Brake Kit

Question

Question:

Is this CE Smith Trailer Idler Hub Assembly for 6,000-lb Axles - 6 on 5-1/2 - Pre-Greased Item # CE13711 compatible with the Kodiak Disc Brake Kit - 12inch Rotor - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs Item # K2R526D? Thanks!

asked by: Jacob

0

Expert Reply:

The Kodiak Disc Brake Kit part # K2R526D is compatible with pretty much any idler hub with a 6 on 5-1/2" bolt pattern therefore you won't have any issues with the CE Smith Trailer Idler Hub Assembly part # CE13711. I have attached an install video I did on the brake kit for you as well.

expert reply by: Conner L

0

Answer 1

The Electric Trailer Brake Kit part #AKEBRK-7-D is exactly what you need to replace the 12" diameter x 2" wide electric brakes on your horse trailer with AL-KO 6,000 lb axles. However, the dacromet finish is only really needed for boat…

view full answer...

Answer 2

Yes, the 3" length of the shank is measured from the end of the spine to the mounting flange of the Trailer Idler Hub Assembly #52655IEU. I have noted that and the 2-1/4" diameter in the attached photo for you to reference as well. This…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...