Recommended Roof Vent Lid For 2007 Winnebago Outlook Motorhome

Question

Question:

I need a vent cover for 2007 winnebago outlook It seems like the 14x14 is too big is there a 13 x 13

asked by: Richard L

0

Expert Reply:

I have another option for you, but roof vents are only 14" x 14", and we do not have any smaller covers.

If you can tell me what the model number of your roof vent is I would be happy to confirm the correct replacement roof vent lid for you, or you can use the MaxxAir UniMaxx Universal Replacement Lid # MA00-335001 in white or # MA00-335002 in smoke.

Both options mentioned are universal and use a universal hinge that gets screwed to your existing roof vent so they will work with any roof vent made.

I included videos of the products mentioned for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 3

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 4

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 5

On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…

view full answer...

Answer 6

Yes we have a 14 inch version of the Aluminum Viking Series Valhalla trailer wheel with the part #AX02455545BMFL. This is 5-1/2 inches wide and has the standard 5 on 4-1/2 inch bolt pattern that 14 inch trailer wheels have. I attached a picture of…

view full answer...

Answer 7

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 8

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 9

While we don't have any custom fit trailer wiring harnesses that fit the 2011 Isuzu NPR we can still help with a universal fit option like the #C56175 which you'd have to wire to the taillight circuits of your NPR.

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...