Can 96 Inch Long x 3 Inch Wide Rubber Bumper be Used With 12 Inch Bolt Spacing

Question

Question:

The bumper says the holes are at 11”, but it measures 12” on my trailer. Is there one that I can order for 12” bolt spacing

asked by: Autumn

0

Expert Reply:

While there isn't a bumper that has 12 inch bolt hole spacing, you can still use the 96" long x 3" wide Pre-Drilled Round Rubber Trailer Bumper # D3-96.

What you could do is drill the necessary holes at the spacing you need and it will work for you.

expert reply by: Kyle S

0

Answer 1

Since the Redline Pre-Drilled Round Bumpers, part #D3-96, part #D2-96, and part #D4-96, are made of rubber I see no reason why you cannot drill out mounting holes so that they are custom to your hole patterns. If you will be using the full 96 inches…

view full answer...

Answer 2

What you'd want to do is drill holes in the Pre-Drilled Round Rubber Trailer Bumper #D3-96 to match the mounting holes of your trailer and you'd be set. The bumper is rubber so it would be easy to drill. The pre drilled holes of this are 11…

view full answer...

Answer 3

We have 3 different rubber bumpers that you can use for your horse trailer. They all measure 96" long but have different widths so you'll just need to choose the appropriate width: 2-1/16" Width - #D2-96 3" Width - #D3-96 4"…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Philip so while we don't carry the exact spring you are looking for it does match the specs of the #e59SR so this would be a great solution. It's correct length at 23-1/8 inches and is for a 3,500 lb trailer axle like you have as well.

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

Hi Kat, The rubber bumpers that we offer are all 96" in length but can come in different widths. Based on the dimensions you provided i your pictures the #D3-96 is going to be the best fit, but you will have to cut it down to size.

view full answer...

Answer 8

The bumper part #D3-96 that you referenced is our best option and could work for you but you will need to make some modifications. You would need to cut it down to the 84 inch length you need and would also need to drill new holes in it that line up…

view full answer...

Answer 9

The part number 072-097-00 is for a Dexter leaf spring. Our closest equivalent would be the 5-Leaf Double-Eye Spring item #e34SR. This is a 3,000 lbs spring that works with 6,000 lbs axles. It measures 25-1/4" long from eye hole to eye hole.…

view full answer...

Answer 10

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 11

All of our bumper strips are 96" long and have the holes pre-drilled out at 11" on center, but the nice thing is these can be cut and re-drilled to accommodate your application. You just need to choose which one has the width you're…

view full answer...

Can 96 Inch Long x 3 Inch Wide Rubber Bumper be Used With 12 Inch Bolt Spacing

Product Page this Question was Asked From

Continue Researching