Can a Weight Distribution System be Used on a V-Nose Trailer With 22 Inches of Useable A-Frame?

Question

Question:

Im trying to install a weight distribution hitch on my truck/trailer but the A-frameinch on my trailer only has 22 inches of beam exposed. It seems none of they systems work with such a short section available. Any help would be appreciated. Photo attached. Trailer GVWR is 7,000 lbs. Hope you can help.

asked by: Randall S

0

Expert Reply:

If you are getting sway issues, I can definitely recommend the Tuson Asymmetric Sway Control # 335TSC-1000. But from the picture and measurements provided, it does not look like we will have a weight distribution option available.

I would usually suggest a Curt Short-Arm Weight Distribution System, like the # C17332, but the arms on this, though shorter than typical systems, are still going to be too long.

expert reply by: Lazer S

0

V-Nose Trailer
(click to enlarge)

Answer 1

Yes, the Strait-Line Weight Distribution Hitch System can be adapted to a V-Nose style trailer. You would need to use an alternate mounting system for the chain hanger brackets. The Bolt on Chain Hanger Kit, item #RP58305, will bolt onto the side…

view full answer...

Answer 2

A trailer with accessories like propane tanks up front or with V-nose construction like yours can make it more challenging to install a weight distribution (WD) system. WD spring bar brackets typically need to mount 25 - 30-inches behind the hitch…

view full answer...

Answer 3

We don't have a combo of the Curt Hitch Ball #C40008 and Curt Ball Mount #C45340. The ball mount is extremely heavy-duty, rated up to 17,000 pounds. I think it's safe to assume you don't have a torque wrench rated up to 450 foot pounds…

view full answer...

Answer 4

You'd need to go with a Short Arm Curt weight distribution system like the part #C17330 which has a 600 lb tongue weight max, the #C17331 for if you need an 800 lb max TW rating, or #C17332 for if you need a 1,000 lb tongue weight max system. The…

view full answer...

Answer 5

For your NEO NMS2685TR with the enclosed V-nose, the Reese Friction Sway Control Kit #83660 is the best option. Because of the length of your trailer, two are recommended. You can use the Reese Sway-Control Bracket for 2" Ball Mounts #RP26003…

view full answer...

Answer 6

Thank you for the photo of your v-nose enclosed trailer for which you are looking for a weight distribution/sway control (WD/SC) system. Since you have limited access to the trailer frame, about 15-inches based on your photo, I suggest you check…

view full answer...

Answer 7

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Hello Steve. I do have a good solution for you, but I cannot recommend using the Malone Adapter #MPG544. Since it is rated for towing only 4,000 lbs, your 8,000 lb towed vehicle would be double the max towing capacity. You are right about there being…

view full answer...