Parts Needed to Install a Trailer Brake Controller on a 1999 Ford E-350 Econoline Van

Question

Question:

I have a 1999 E-350 Super Duty extended van 15 passanger. I plan on towing a 2006 air stream trailer 7900 lbs. I looked under the back of the van and there is no harness which would come apart to connect a T connector to. I dont have a tow package but plan on installing a transmission and oil cooler. I know I will also need a brake controller. I viewed your site and the only video I saw was for a club wagon 1996 van which I believe is the same for the hook up. Your help is greatly appreciated.

asked by: Philip G

0

Expert Reply:

In order to install a brake controller on your 1999 Ford E-350, the first thing you are going to need is a 4-Way trailer connector # 118344. I have included a link to the isntallation instructions for you to view.

Next you will need a 4 and 7-Way installation kit # ETBC7. This will provide the 7-Way, while retaining the use of the 4-Way, and all of the wiring needed to install the brake controller. I have included some links that will explain the ETBC7 installation for you.

And finally you will need the brake controller. I recommend the Tekonsha P2, # 90885, because it is easy to set up, easy to use, and is very reliable. I have linked its instructions for you to view.

You mentioned adding a transmission cooler and oil cooler. I recommend a combination cooler that has inlets for both. Take a look at combination cooler # D15902. It has everything you will need to have a transmission and engine oil cooler in one unit. I have provided some FAQ links on coolers for you.

expert reply by: Michael H

0

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 6

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 7

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 8

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 9

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 10

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 11

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...