Does GloLight LED Combination Trailer Tail Light STL161RLB Have Built In Side Marker Light?

Question

Question:

Does this light serve as a side marker rear light as well?

asked by: Steve

0

Expert Reply:

The GloLight LED Combination Trailer Tail Light - 5 Function - Submersible - 39 Diodes - Driver Side # STL161RLB you were looking at does not have a built in side marker light, so you would need to add a side marker light using # 328-K-52.

Another option would be to use the Blazer LED Trailer Tail Light - Submersible - 6 Function - 7 Diodes - Red Lens - Passenger Side # C7493RTM and Driver Side # C7483RTM instead which do have the built in side marker lights.

I included videos of the products mentioned for you to take a look at.

expert reply by: Samuel C

0

Answer 1

We have a few options for your coupler with a 4-1/2" lip. The etrailer Trailer Coupler Lock #e98895 is a good lock. From there we move up to the better Trimax Dual Purpose Coupler Lock #TMX67FR which uses a hardened steel construction. The…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

We had a customer who was able to replace his Dexter 8-155 hubs with the #8-201-5UC3-EZ that you referenced so they should work well for you. You can verify that this hub will work for you by pulling your current hub and making sure they have inner…

view full answer...

Answer 5

I looked up your Dexter 8-222 Hub and was able to find the inner and outer bearing numbers as well as the grease seal used. It looks like this particular hub was designed for mobile homes and these, for the most part, have more unique bearings and…

view full answer...

Answer 6

Yes the Replacement Brass Connector #T4750300 for Titan Disc Brake Actuators will fit a Tie Down 660e disc brake actuator.

view full answer...

Answer 7

To replace your AL-KO 568303 seal you will want the Oil Seal #91030. This seal has the same inner diameter of 2.750 inches and outer diameter of 3.779 inches. It is a confirmed fit for your #99 spindle that uses the AL-KO 568303 seal.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

Yes, the Kodiak Disc Brake Caliper #KDBC250D will fit the caliper bracket that comes in the HydraStar Disc Brake Kits, like Kit #HSE7K-T1. We also have the Stainless Steel Kodiak Disc Brake Caliper #KDBC250S and Stainless Steel Ceramic Brake Pads…

view full answer...

Answer 12

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...