Is the Pull Pin Easy Swivel Trailer Jack DL22580 Strong Enough For A 4000lb Trailer?

Question

Question:

Im looking for a tongue jack that I can mount on the side of my 5inch A frame or into the front-centre mount of the A frame of my 4000lb RV Trailer which has a hitch weight of 450lbs. Does the 1500lb weight capacity of this tongue jack refer to the hitch weight or actual trailer weight? I need to move my trailer around to a spot on my driveway where I cannot do it attached to my tow vehicle. Will this hitch be durable enough to do that? Or can you recommend another?

asked by: Chris

0

Expert Reply:

The Pull Pin, Easy Swivel Trailer Jack with 6" Dual Wheels - Sidewind - 1,500 lbs. # DL22580 you were looking is designed to fit trailer tongues that are up to 3" wide x 5" tall, so this will be perfect for the frame of your trailer.

Since the only weight that affects a trailer jack is the tongue weight, and since you only have 450lbs of tongue weight this jack will be plenty strong as it has a 1500lb rating.

In addition the dual wheels on the # DL22580 will be perfect for allowing you to move the trailer around in your driveway by hand as needed.

I included a video of the # DL22580 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Thank you for the pictures! For a replacement option I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX29FR to replace your current actuator. The #DX29FR has a 7500lb trailer weight…

view full answer...

Answer 11

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...