Parts Needed To Install EcoHitch Trailer Hitch Receiver 306-X7239 On 2013 Ford Fusion
Question:
When installing the hitch receiver on a 2013 Ford Fusion Titanium, once the panel is removed is there a speaker that will require the Speaker Bracket? IF so what parts are all needed? Also with how low the car already is can a hitch ball mount but used upside downinch to be used as a riser?
asked by: Kim P
Expert Reply:
There is not always a speaker behind the rear bumper on the Ford Fusion, so you will need to check under the bumper to see if your particular 2013 Ford Fusion has the speaker or not.
If you do you will need the # 18136 to make a bracket to move it out of the way of the EcoHitch Trailer Hitch Receiver # 306-X7239. You will also need to source two nuts and bolts to secure the speaker to the bracket.
You can absolutely use a ball mount upside down to get the correct rise needed to tow your trailer level. To determine how much rise you will need you will need to level your trailer and measure from the ground to the bottom of the coupler of your trailer.
When we installed the # 306-X7239 on a similar 2020 Ford Fusion we found that from the ground to the top inside edge of the receiver was 10". The difference between these two measurements will be the amount of rise you need to tow your trailer level.
If you can tell me how much rise you need I would be happy to recommend the correct ball mount. I went ahead and included a link to all of our ball mounts for you to look through as well.
Lastly to complete your towing setup you will need a vehicle wiring harness # 118574.
I included installation videos for both of the products mentioned for you to take a look at.
Products Referenced in This Question
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Round
- 5 Round
- 6 Round
- Tow Ready
more information >
Product Page this Question was Asked From
EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- EcoHitch
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Best Bike Rack for 65-LB Bikes with a Tilt-Away Feature for a 2" Receiver
- Search Results: ebike carrier
- Search Results: class 3 trailer hitch
- Search Results: class 3 hitch
- Article: Best Bike Racks for Electric Bikes
- Shop: Curt Bike Rack for 2 Electric Bikes - 2" Hitches - Wheel Mount
- Shop: Hollywood Racks Destination Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
- Shop: EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Multi Fit - Class III - 2"
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Swagman Current Bike Rack for 2 Electric Bikes - 1-1/4" and 2" Hitches - Frame Mount
- Q&A: E Bike Rack Recommendation for 70 lb Bike
- Q&A: Best Fat Tire E-Bike Bike Racks for Class 1 Trailer Hitch
- Search Results: 1.25 inch hitch bike rack
- Search Results: class 1 hitch
- Q&A: Installation Instructions for EcoHitch Hidden Trailer Hitch # 306-X7317
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Wiring
- Search Results: trailer hitch
- Video: Choosing the Right Trailer Wiring
- Video: Tow Ready 4-Pole Mounting Bracket Installation
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: hitch
- Shop: Roof Rack
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado